Featured image:
The Toyota Supra Mk5 is a high-performance sports car that is known for its sleek design and powerful engine. However, like all vehicles, the Supra Mk5’s seat belts can become worn or damaged over time. If you need to replace the seat belt in your Supra Mk5, it is important to follow the correct steps to ensure that the new seat belt is installed properly and safely.
Replacing the seat belt in a Toyota Supra Mk5 is not a difficult task, but it is important to take your time and follow the steps carefully. Before you begin, you will need to gather the following tools: a 10mm socket wrench, a 12mm socket wrench, a flathead screwdriver, and a new seat belt. Once you have gathered your tools, you can begin the replacement process.
First, you will need to remove the old seat belt. To do this, locate the two 10mm bolts that are holding the seat belt in place. Once you have found the bolts, remove them using the 10mm socket wrench. Once the bolts have been removed, you can pull the seat belt out of the vehicle. Next, you will need to install the new seat belt. To do this, insert the new seat belt into the vehicle and line up the holes in the seat belt with the holes in the vehicle. Once the holes are lined up, insert the two 10mm bolts and tighten them using the 10mm socket wrench. Finally, you will need to test the new seat belt to make sure that it is working properly.
Identifying and Accessing Seat Belt Mounting Points
Identifying Seat Belt Mounting Points
The seat belt mounting points in a Toyota Supra Mk5 are located in various positions within the vehicle’s interior. Identifying these points is essential before attempting to replace the seat belt:
-
Front Seat Belts: The front seat belts are mounted at three points. The upper mounting point is situated on the B-pillar, while the two lower mounting points are located on the floor below the front seats.
-
Rear Seat Belts: The rear seat belts are mounted at four points. The two upper mounting points are located on the C-pillars, while the two lower mounting points are located on the sidewalls behind the rear seats.
-
Shoulder Belts: The shoulder belts are mounted at two points. The upper mounting point is situated on the B-pillar or C-pillar, depending on the seat location, while the lower mounting point is located on the rear parcel shelf.
Accessing Seat Belt Mounting Points
Once the seat belt mounting points have been identified, it is necessary to access them in order to replace the seat belt. This may involve removing trim panels, seat cushions, or other components that obstruct access to the mounting points.
-
Front Seat Belts: Accessing the front seat belt mounting points requires removing the lower seat cushion and the side trim panels.
-
Rear Seat Belts: Accessing the rear seat belt mounting points requires removing the side trim panels and the rear parcel shelf.
-
Shoulder Belts: Accessing the shoulder belt mounting points requires removing the trim panel located near the upper mounting point on the B-pillar or C-pillar.
| Seat Belt | Upper Mounting Point | Lower Mounting Point |
|---|---|---|
| Front Seat Belts | B-pillar | Floor below front seats |
| Rear Seat Belts | C-pillars | Sidewalls behind rear seats |
| Shoulder Belts | B-pillar or C-pillar | Rear parcel shelf |
Inspecting and Preparing New Seat Belt
1. Examine the Seat Belt
Thoroughly inspect the new seat belt for any visible damage or defects. Look for tears, frays, or cuts in the webbing. Check the buckle and retractor mechanism for proper operation. If you notice any issues, do not install the seat belt and contact the manufacturer for a replacement.
2. Gather Necessary Tools
Gather the following tools before beginning the replacement process: a socket wrench or spanner, pliers, and a flathead screwdriver. You may also need a flashlight for better visibility while working in tight spaces.
3. Disconnect the Battery
Safety first! Disconnect the negative terminal of the battery to prevent any potential electrical hazards during the installation.
4. Remove the Old Seat Belt Components
Locate the bolts that secure the seat belt to the vehicle frame. Using the socket wrench, remove the bolts and detach the seat belt assembly from the frame. Disconnect the buckle and retractor mechanism from the seat. Carefully remove the seat belt from the vehicle.
Detailed Instructions for Removing Seat Belt Components:
a. Front Seat Belt
| Step | Description |
|---|---|
| Locate | Identify the two bolts that connect the seat belt to the B-pillar and the floor |
| Remove | Use the socket wrench to unscrew the bolts and detach the seat belt |
| Disconnect | Unclip the buckle and retractor mechanism from the seat |
b. Rear Seat Belt
| Step | Description |
|---|---|
| Locate | Find the bolt that secures the seat belt to the rear body panel |
| Remove | Use the socket wrench to remove the bolt and detach the seat belt |
| Disconnect | Unclip the buckle from the seat |
How To Replace Seat Belt In Toyota Supra Mk5
Replacing a seat belt in a Toyota Supra Mk5 is a relatively straightforward process that can be completed in about an hour. Here are the steps on how to do it:
1.
Disconnect the negative battery terminal.
2.
Locate the seat belt bolt on the bottom of the seat. Remove the bolt and then pull the seat belt out of the seat.
3.
Unbolt the seat belt retractor from the car frame. Disconnect the electrical connector from the retractor.
4.
Install the new seat belt retractor and connect the electrical connector.
5.
Insert the seat belt into the seat and bolt it down.
6.
Reconnect the negative battery terminal.
How much does it cost to replace a seat belt in a Toyota Supra Mk5?
Replacing a seat belt in a Toyota Supra Mk5 will typically cost between $100 and $200 for parts and labor.
What are the symptoms of a bad seat belt in a Toyota Supra Mk5?
There are several symptoms that may indicate a bad seat belt in a Toyota Supra Mk5, including:
1.
The seat belt does not retract properly.
2.
The seat belt is frayed or damaged.
3.
The seat belt buckle does not latch properly.
4.
The seat belt warning light is illuminated.
