Garbage disposals are a convenient way to get rid of food scraps and other waste, but they can also be a pain to clean. If your garbage disposal is clogged or not working properly, you may need to take it out to clean it or replace it. Taking out a garbage disposal can be a challenging task, but it is possible to do it yourself with the right tools and instructions. Keep reading this article to learn how to take out a garbage disposal and a few other important tips you must know.
Before you start, you will need to gather a few tools. You will need a wrench, a screwdriver, a bucket, and a pair of pliers. You may also need a flashlight to see inside the disposal. Once you have your tools, you can begin the process of removing the garbage disposal. First, you will need to turn off the power to the disposal. You can do this by flipping the breaker that powers the disposal. Once the power is off, you can begin disconnecting the plumbing. Use the wrench to disconnect the water supply lines. Then, use the pliers to disconnect the drain line. Once the plumbing is disconnected, you can remove the garbage disposal from the sink. To do this, use the screwdriver to remove the mounting screws. Once the screws are removed, you can lift the garbage disposal out of the sink.
Once you have removed the garbage disposal, you can clean it or replace it. If you are cleaning the disposal, you can use a degreaser to remove any grease or grime. You can also use a brush to scrub away any food particles. Once the disposal is clean, you can reassemble it and reinstall it in the sink. To reinstall the disposal, simply reverse the steps that you used to remove it. First, connect the drain line to the disposal. Then, connect the water supply lines to the disposal. Finally, secure the disposal to the sink using the mounting screws. Once the disposal is reinstalled, you can turn the power back on and test it to make sure it is working properly.
Remove the Drain Plug
To obtain better access to the garbage disposal, you ought to remove the drain plug. This plug is normally found in the center of the sink’s drain. To remove it, you’ll need a pair of pliers or a similar tool. Simply grip the plug with the pliers and twist it counterclockwise to loosen it. Once the plug is loose, you can pull it out with your hand.
Locating the Reset Button
The reset button is typically located on the bottom of the disposal. It may be covered by a rubber cap or a plastic cover. Once you have located the reset button, press it firmly to reset the disposal. You may need to press the button several times to fully reset the disposal.
Steps to Reset the Disposal
| Step | Instruction |
|---|---|
| 1 | Unplug the disposal from the power outlet. |
| 2 | Locate the reset button on the bottom of the disposal. |
| 3 | Press the reset button firmly several times. |
| 4 | Plug the disposal back into the power outlet. |
| 5 | Turn on the water and run the disposal to test if it has been successfully reset. |
Locate the Reset Button
If your garbage disposal has stopped working, the first thing you should do is try to reset it. The reset button is usually located on the bottom or side of the disposal unit. It may be a small, red button that says “reset” or “reset circuit breaker.”
To reset the disposal, simply press the button. You may hear a clicking sound, and the disposal should start working again.
If the reset button does not work, you may need to unplug the disposal from the power outlet and wait a few minutes before plugging it back in. This will allow the disposal to cool down and reset itself.
If you are still having trouble resetting your garbage disposal, you may need to call a plumber.
Here is a table with some tips on how to locate the reset button on your garbage disposal:
| Disposal Brand | Reset Button Location |
|---|---|
| InSinkErator | Bottom of the disposal unit, near the power cord |
| KitchenAid | Side of the disposal unit, near the bottom |
| Waste King | Bottom of the disposal unit, near the center |
| Whirpool | Side of the disposal unit, near the top |
Remove the Impeller
The impeller is the most important part of a garbage disposal, so it’s important to take care when removing it. Here are the steps on how to safely remove the impeller:
- Turn off the power to the garbage disposal. This is important to prevent any accidents.
- Disconnect the water from the garbage disposal. This will help to prevent any water from leaking out when you remove the impeller.
- Remove the screws that hold the impeller in place. There are usually three or four screws that hold the impeller in place. Once the screws are removed, you should be able to pull the impeller straight out.
- Inspect the impeller for any damage or wear. If the impeller is damaged, you will need to replace it.
- Clean the impeller and the inside of the garbage disposal. This will help to remove any food particles or debris that may have accumulated. To clean the impeller, use a brush or a sponge to remove any food particles or debris. To clean the inside of the garbage disposal, use a mixture of baking soda and vinegar. Pour the baking soda and vinegar down the drain and let it sit for a few minutes. Then, use a brush or a sponge to scrub the inside of the garbage disposal. Finally, rinse the garbage disposal with water.
- Reinstall the impeller. Once the impeller and the inside of the garbage disposal are clean, you can reinstall the impeller. To do this, simply align the impeller with the shaft and push it into place. Then, tighten the screws to hold the impeller in place.
- Reconnect the water to the garbage disposal. Once the impeller is reinstalled, you can reconnect the water to the garbage disposal.
- Turn on the power to the garbage disposal. Once the water is reconnected, you can turn on the power to the garbage disposal.
Reinstall the Impeller
Once you’ve removed the impeller, it’s time to reinstall it. Here are the steps:
- Align the impeller with the shaft.
- Push the impeller down onto the shaft until it clicks into place.
- Tighten the impeller screw.
- Reassemble the disposal body.
- Reattach the disposal body to the sink flange.
- Tighten the mounting bolts.
- Reconnect the electrical cord.
Once you’ve reinstalled the impeller, test the disposal to make sure it’s working properly.
Troubleshooting
If the disposal doesn’t work after you’ve reinstalled the impeller, there may be a problem with the impeller or the motor. Here are some troubleshooting tips:
| Problem | Solution |
|---|---|
| The impeller won’t spin. | The impeller may be jammed. Try to remove the impeller and clean it. If the impeller is still jammed, you may need to replace it. |
| The motor is humming but the impeller won’t spin. | The motor may be burned out. You will need to replace the motor. |
| The disposal is leaking. | The disposal may have a leak in the body or the drain line. Tighten the mounting bolts or replace the drain line. |
Replace the Drain Plug
Now that the disposal is uninstalled, you need to replace the drain plug.
1. Locate the drain plug. It is usually a black rubber plug located in the center of the sink drain.
2. Remove the old drain plug. Use a pair of pliers to grip the plug and pull it out of the drain.
3. Clean the drain hole. Use a sponge or cloth to clean any debris from the drain hole.
4. Insert the new drain plug. Push the new drain plug into the drain hole until it is snug.
5. Tighten the drain plug. Use a pair of pliers to tighten the drain plug until it is secure.
6. Test the drain plug. Run water into the sink and check for any leaks.
7. Reinstall the garbage disposal. Follow the steps in the previous section to reinstall the garbage disposal.
8. Check for leaks. Once the garbage disposal is reinstalled, run water into the sink and check for any leaks. If there are any leaks, tighten the drain plug or the garbage disposal until the leaks stop.
Reconnect the Power
9. **Reconnect the Power**
Once the disposal is out, the next step is to reconnect the power. This can be done by following these steps:
- Inspect the Wires: Before reconnecting the power, inspect the wires to make sure they are not damaged. If any wires are frayed or cut, they will need to be replaced.
- Disconnect the Wires: Disconnect the wires from the disposal by unscrewing the wire nuts. Keep track of which wire goes to which terminal so that you can reconnect them correctly.
- Strip the Wires: Strip about 1/2 inch of insulation from the ends of the wires.
- Connect the Wires: Connect the wires to the terminals on the disposal. The black wire goes to the “L” terminal, the white wire goes to the “N” terminal, and the green wire goes to the “G” terminal.
- Tighten the Wire Nuts: Tighten the wire nuts securely to hold the wires in place.
- Turn on the Power: Turn on the power at the circuit breaker or fuse box. The disposal should now be operational.
If the disposal is not working after reconnecting the power, check the following:
| Problem | Solution |
|---|---|
| The disposal does not turn on. | Check the circuit breaker or fuse to make sure it is not tripped or blown. |
| The disposal makes a humming noise but does not grind. | The flywheel may be jammed. Try using a broom handle or other long object to manually turn the flywheel. |
| The disposal leaks water. | The disposal may not be properly sealed. Check the gaskets and seals and replace them if necessary. |
How To Take Out Garbage Disposal
If your garbage disposal is clogged or not working properly, you may need to take it out to clean or repair it. Here are the steps on how to take out a garbage disposal:
1. **Turn off the power to the garbage disposal.** This can be done by flipping the circuit breaker or removing the fuse that powers the disposal.
2. **Disconnect the water supply to the garbage disposal.** This can be done by turning off the shut-off valve under the sink.
3. **Loosen the mounting nuts that hold the garbage disposal in place.** There are usually three or four nuts that need to be loosened.
4. **Carefully lower the garbage disposal out of the sink.** Be careful not to drop the disposal, as it is heavy.
5. **Once the garbage disposal is out of the sink, you can clean or repair it as needed.**
6. **To reinstall the garbage disposal, simply reverse the steps above.**
People Also Ask About How To Take Out Garbage Disposal
How do I know if my garbage disposal is broken?
There are a few signs that may indicate that your garbage disposal is broken:
- The disposal is not turning on.
- The disposal is making a loud noise.
- The disposal is leaking water.
- The disposal is not grinding food properly.
How do I reset my garbage disposal?
To reset your garbage disposal, simply press the reset button on the bottom of the disposal. If the disposal does not reset, you may need to unplug it from the power outlet and then plug it back in.
How do I clean my garbage disposal?
To clean your garbage disposal, you can use a mixture of baking soda and vinegar. Pour 1/2 cup of baking soda down the drain, followed by 1/2 cup of vinegar. Let the mixture sit for 15 minutes, then flush the drain with hot water.
