Attention all motorcycle enthusiasts and Honda CL175 owners! Have you struggled to remove the ignition switch from your beloved 1970 Honda CL175, but couldn’t find any guidance due to the lack of a title? Fear not, as we delve into the intricacies of this task, providing you with a comprehensive guide that will empower you to tackle this challenge with confidence, regardless of the absence of a title.
Before embarking on this adventure, it’s crucial to gather the necessary tools. You’ll need a Phillips head screwdriver, a flathead screwdriver, and a set of needle-nose pliers. Additionally, having a small flashlight or work light can be beneficial for illuminating the work area and ensuring precision. With these tools at your disposal, you’re well-equipped to navigate the process of removing the ignition switch from your 1970 Honda CL175.
Disconnect the Battery
Before beginning any electrical work on your 1970 Honda CL175, it is crucial to disconnect the battery to prevent any electrical shorts or damage to the electrical components. Follow these steps to safely disconnect the battery:
- Locate the battery, which is usually placed under the seat or near the engine.
- Identify the negative (-) and positive (+) terminals of the battery.
- Using a wrench or socket, loosen the bolt or nut connecting the negative terminal to the battery. Make sure to remove the terminal completely.
- Repeat the process for the positive terminal. Once both terminals are disconnected, the battery is now safely isolated from the electrical system.
It is important to note that you should never disconnect the positive terminal first, as this could create a spark that could ignite any flammable vapors present.
| Tool Required | Size |
|---|---|
| Wrench or Socket | Varies depending on bolt/nut size |
Remove the Handlebar Covers
To remove the handlebar covers, you will need a Phillips head screwdriver.
1. Locate the two screws on the underside of each handlebar cover.
2. Use the screwdriver to remove the screws.
3. Gently pull the handlebar cover away from the handlebar. It may be necessary to use a small amount of force.
4. Repeat steps 1-3 for the other handlebar cover.
Detailed Instructions for Step 4: Removing the Right Handlebar Cover
- Locate the access hole on the underside of the right handlebar cover. This hole is located near the center of the cover.
- Insert a small screwdriver or Allen key into the access hole. Rotate the screwdriver counterclockwise to release the handlebar cover.
- Gently pull the handlebar cover away from the handlebar. It may be necessary to use a small amount of force.
| Step | Action |
|---|---|
| 1 | Locate the two screws on the underside of each handlebar cover. |
| 2 | Use the screwdriver to remove the screws. |
| 3 | Gently pull the handlebar cover away from the handlebar. It may be necessary to use a small amount of force. |
Disconnect the Electrical Connections
Once the ignition switch is exposed, you need to disconnect the electrical connections. This involves unplugging the wires that are connected to the switch.
The wires are usually attached to terminals on the switch. To unplug the wires, you need to use a small flathead screwdriver or a pick tool. Gently pry the terminal open and pull the wire out.
Once all of the wires are disconnected, you can remove the ignition switch from the motorcycle. To do this, simply unscrew the mounting screws and pull the switch out.
Here is a more detailed guide on how to disconnect the electrical connections:
- Locate the ignition switch. It is usually located on the right side of the handlebars.
- Identify the wires that are connected to the switch. The wires will be different colors, and they will be attached to terminals on the switch.
- Use a small flathead screwdriver or a pick tool to pry open the terminals.
- Pull the wires out of the terminals.
- Once all of the wires are disconnected, you can remove the ignition switch from the motorcycle.
Here is a table that summarizes the steps involved in disconnecting the electrical connections:
Step Description 1 Locate the ignition switch. 2 Identify the wires that are connected to the switch. 3 Use a small flathead screwdriver or a pick tool to pry open the terminals. 4 Pull the wires out of the terminals. 5 Once all of the wires are disconnected, you can remove the ignition switch from the motorcycle. Loosen the Clamping Bolts
The ignition switch on a 1970 Honda CL175 is held in place by two clamping bolts. To remove the ignition switch, you will need to loosen these bolts. Use a 10mm socket wrench or a 10mm open-end wrench to loosen the bolts. Turn the bolts counterclockwise to loosen them. Once the bolts are loose, you can remove the ignition switch.
Here is a table summarizing the steps for loosening the clamping bolts:
Step Action 1 Locate the two clamping bolts that hold the ignition switch in place. 2 Use a 10mm socket wrench or a 10mm open-end wrench to loosen the bolts. 3 Turn the bolts counterclockwise to loosen them. Once the bolts are loose, you can remove the ignition switch by pulling it straight out of the dash.
Unbolt the Ignition Switch
Locate the two bolts that hold the ignition switch in place. These bolts are usually located on either side of the switch.
Using a socket wrench or a screwdriver, remove the bolts.
Once the bolts are removed, you will be able to pull the ignition switch out of the dashboard.
Disconnect the Electrical Connector
Once the ignition switch is removed from the dashboard, you will need to disconnect the electrical connector.
The electrical connector is usually located on the back of the ignition switch.
To disconnect the electrical connector, simply press on the release tab and pull the connector apart.
Remove the Ignition Switch
Once the electrical connector is disconnected, you will be able to remove the ignition switch.
To remove the ignition switch, simply pull it straight out of the dashboard.
Reinstall the Ignition Switch
To reinstall the ignition switch, simply insert it into the dashboard and tighten the two bolts.
Once the bolts are tightened, the ignition switch will be secure.
Reconnect the electrical connector by pressing on the release tab and pushing the connector into place.
Test the Ignition Switch
Once the ignition switch is reinstalled, you should test it to make sure it is working properly.
To test the ignition switch, simply insert the key and turn it to the “on” position.
If the ignition switch is working properly, the engine will start.
How To Remove Ignition Switch From 1970 Honda CL175
1. **Disconnect the battery.** This is important to do before you start working on any electrical components, as it will prevent any accidental shocks or damage to the electrical system.
2. **Locate the ignition switch.** It is usually located on the right side of the handlebars, near the throttle.
3. **Remove the two screws that hold the ignition switch in place.**
4. **Pull the ignition switch straight out of the housing.**
5. **Disconnect the electrical connectors from the back of the ignition switch.**
6. **Remove the ignition switch from the motorcycle.
People Also Ask
How do I know if my ignition switch is bad?
There are a few symptoms that can indicate a bad ignition switch, including:
- The motorcycle will not start.
- The motorcycle starts intermittently.
- The motorcycle stalls while riding.
- The ignition switch feels loose or wobbly.
How much does it cost to replace an ignition switch?
The cost of replacing an ignition switch will vary depending on the make and model of the motorcycle, as well as the labor costs of the mechanic. However, you can expect to pay between $50 and $200 for the part and labor.
Can I replace the ignition switch myself?
Yes, it is possible to replace the ignition switch yourself. However, it is important to have some basic mechanical skills and knowledge of motorcycle electrical systems before attempting this repair.
