If you’re like most people, you probably don’t think about your car’s cabin air filter very often. But did you know that a dirty cabin air filter can actually make you sick? That’s because a dirty cabin air filter can trap pollutants like dust, pollen, and bacteria, which can then be circulated throughout your car’s interior. This can lead to a number of health problems, including allergies, asthma, and respiratory infections.
The good news is that changing your cabin air filter is a relatively easy and inexpensive way to improve your car’s air quality and protect your health. In this article, we’ll show you how to access the cabin air filter in a 2008 Honda CR-V. We’ll also provide some tips on how to choose the right cabin air filter for your car.
The cabin air filter is located behind the glove box. To access it, you’ll need to remove the glove box. To do this, first open the glove box and remove its contents. Then, locate the two screws that hold the glove box in place and remove them. Next, gently pull the glove box towards you until it comes loose. Finally, lift the glove box up and out of the way.
Identifying the Cabin Air Filter Location
The 2008 Honda CR-V’s cabin air filter plays a vital role in maintaining a clean and comfortable environment within your vehicle. By replacing this filter regularly, you can significantly improve the air quality you and your passengers breathe. To locate the cabin air filter in your Honda CR-V, follow these comprehensive steps:
Accessing the Glove Box
1. Begin by opening the glove box and removing its contents.
2. Locate the two small, plastic release levers on the sides of the glove box.
3. Squeeze the release levers and gently pull the glove box downward to release it from its housing.
Finding the Cabin Air Filter Housing
4. Once the glove box is removed, you will notice the rectangular-shaped cabin air filter housing situated behind it.
5. The housing is typically secured by a few screws or plastic clips. Using a screwdriver or your fingers, carefully remove these fasteners.
Removing the Cabin Air Filter
6. With the housing now accessible, locate the cabin air filter within it.
7. Gently slide the filter out of its slot by pulling it towards you.
8. Note the orientation of the old filter and ensure the new filter is installed in the same direction when replacing it.
Gathering Tools and Materials
To access the cabin air filter on a 2008 Honda CRV, you will need the following tools and materials:
Tools:
- Phillips head screwdriver
- Flashlight (optional)
Materials:
- New cabin air filter
- Clean rags or paper towels
Additional Notes:
It is recommended to use a new cabin air filter every 12,000 to 15,000 miles or as specified in your vehicle’s maintenance schedule. Choose a filter that is specifically designed for your Honda CRV model and year to ensure proper fit and performance.
Recommended Cabin Air Filters:
| Brand | Model |
|---|---|
| Fram | CF9854 |
| Bosch | 4925 |
| Denso | 4965 |
Opening the Glove Box
Accessing the cabin air filter on a 2008 Honda CR-V involves opening the glove box. Here’s a step-by-step guide:
1. Open the Glove Box
Locate the glove box on the passenger side of the dashboard. Gently pull the handle to open it.
2. Locate the Cabin Air Filter
Inside the glove box, you’ll find a rectangular plastic cover on the right side. This cover has a hinge at the top and is typically held in place by two or three clips.
3. Remove the Cover
Gently squeeze the two or three clips together and lift the cover up and away from the glove box. This will expose the cabin air filter, which is typically a rectangular or square-shaped filter made of pleated paper or foam.
Here are some additional tips for removing the cover:
– If the clips are tight, use a small flat-head screwdriver or trim tool to pry them open.
– Be careful not to damage the cover or the clips when removing it.
– The cover may be slightly different depending on the specific model year of your Honda CR-V.
Locating and Removing the Cover Panel
Before accessing the cabin air filter, locate the cover panel behind the glove box. To remove it:
1. Open the glove box and locate its sides.
2. Squeeze the sides of the glove box inward, then pull it straight out.
3. Once removed, lay the glove box aside.
4. Behind the glove box, locate two black screws with a Phillips head. Use a screwdriver to unscrew them.
5. Grab the bottom of the cover panel and pull it straight down to remove it.
Extracting the Old Filter
To extract the old filter, you’ll need to follow these steps:
1. Remove the Glovebox
Open the glovebox and squeeze the sides to release it from its hinges. Pull it straight toward you to remove it completely.
2. Locate the Filter Cover
Behind the glovebox, you’ll see a black plastic cover with two screws on the top. Remove the screws using a Phillips head screwdriver.
3. Pull Out the Filter
Once the cover is removed, you can grip the old filter and pull it straight out of its housing.
4. Check for Debris
Before inserting the new filter, inspect the housing for any debris or leaves. If there is any, vacuum it out or wipe it away with a clean cloth.
5. Clean the Cover
While the housing is exposed, take a moment to wipe down the filter cover with a damp cloth to remove any dust or dirt. You can also use a disinfectant spray if desired.
6. Install the New Filter
Align the new filter with the housing and insert it gently, making sure it fits snugly into place.
7. Replace the Cover
Place the filter cover back over the housing and secure it with the screws.
8. Reinstall the Glovebox
Align the glovebox with its hinges and push it back into place until it clicks.
Inserting the New Filter
1. Unfold the new filter and orient it correctly within the filter housing. The filter should have an arrow indicating the direction of airflow, which should point towards the passenger compartment.
2. Gently slide the filter into the housing, ensuring it fits snugly without any gaps or obstructions.
3. Once the filter is fully inserted, reattach the filter housing cover and secure it with the screws or clips you removed earlier.
4. Check that the filter housing cover is properly sealed to prevent any air leaks or contaminants from entering the cabin.
5. Reconnect the glove box and restore any other components you may have removed during the process.
6. Start your vehicle and turn on the air conditioning or heating system to circulate fresh air through the newly installed filter. Enjoy cleaner, healthier air quality inside your Honda CR-V.
Reinstalling the Cover Panel
Once the cabin air filter has been replaced, it’s time to reinstall the cover panel. Here are the steps to follow:
1. Align the Cover Panel
Align the cover panel with the opening in the dashboard.
2. Push the Cover Panel In
Push the cover panel into place until it snaps into position.
3. Secure the Cover Panel
Ensure that the cover panel is securely fastened by pressing down on it firmly around the edges.
4. Check for Gaps
Check for any gaps around the cover panel. If there are any gaps, they may need to be sealed with weatherstripping or duct tape.
5. Replace the Screws
Locate the two screws that were removed earlier and replace them. Tighten the screws until they are snug but not overtightened.
6. Connect the Electrical Connector
If there is an electrical connector attached to the cover panel, reconnect it.
7. Close the Glove Box
Close the glove box to complete the process.
| Step | Description |
|---|---|
| 1 | Align the cover panel with the opening in the dashboard. |
| 2 | Push the cover panel into place until it snaps into position. |
| 3 | Secure the cover panel by pressing down on it firmly around the edges. |
| 4 | Check for any gaps around the cover panel and seal them if necessary. |
| 5 | Replace the two screws that were removed earlier. |
| 6 | Reconnect the electrical connector if there is one. |
| 7 | Close the glove box to complete the process. |
6. Removing the Glove Box
Using a screwdriver, carefully release the four screws that hold the glove box in place. You should locate them on the sides and bottom of the box. Pull the glove box gently towards you to detach it from its hinges and set it aside.
7. Locating the Cabin Air Filter
Behind the glove box, you will find an opening that houses the cabin air filter. It is usually covered by a rectangular panel held in place by clips or screws.
8. Removing the Cabin Air Filter
Gently press and release the clips or unscrew the screws on the panel to access the cabin air filter. Then, carefully grip and slide the old filter straight out of the compartment.
Detailed Removal Instructions:
| Step | Description |
|---|---|
| 1 | Locate the two clips on the side of the panel. |
| 2 | Use your fingers to squeeze the clips together. |
| 3 | Pull the panel straight forward to detach it. |
| 4 | Grip the top and bottom edges of the cabin air filter. |
| 5 | Slide the filter straight out of the compartment. |
Accessing the Cabin Air Filter
1. Open the glove box and locate the two tabs on each side.
2. Push the tabs inward and pull the glove box down to release it.
3. Locate the plastic panel behind the glove box.
4. Unclip the panel by pressing on the tabs on its sides and pulling it forward.
5. The cabin air filter is located behind the panel.
6. Slide the old filter out and insert the new one with the arrow facing up.
7. Reinstall the panel and glove box.
Resetting the Maintenance Minder (Optional)
Resetting the Maintenance Minder (Optional)
1. Turn the ignition to the “ON” position (do not start the engine).
2. Press and hold the “SEL/RESET” button on the instrument panel until the “MAINT” indicator flashes.
3. Turn the ignition off and then back on.
4. The “MAINT” indicator will be reset.
Enjoying Improved Cabin Air Quality
Breathing fresh, clean air inside your Honda CR-V not only enhances your driving experience but also promotes your overall well-being. By accessing and replacing the cabin air filter regularly, you can effectively improve the air quality within your vehicle’s interior.
-
Gather Materials: Acquire a new cabin air filter specifically designed for your 2008 Honda CR-V and basic tools, including a flat-head screwdriver.
-
Locate the Glove Box: Open the glove box and look for the release levers on the sides. Squeeze these levers to detach and lower the glove box.
-
Remove the Glove Box: Once the glove box is lowered, lift it gently from the vehicle.
-
Locate the Cabin Air Filter: You will find a rectangular cover with three tabs behind the glove box opening. This is the access panel for the cabin air filter.
-
Release the Access Panel: Press down on the three tabs simultaneously to release the access panel and pull it towards you.
-
Extract the Old Filter: Grasp the old cabin air filter and pull it straight out of its compartment.
-
Insert the New Filter: Align the new filter with the compartment and slide it into place, ensuring the arrow on the filter points towards the passenger compartment.
-
Replace the Access Panel: Take the access panel and align it with the opening. Push the panel in and press down on the tabs to secure it.
-
Reinstall the Glove Box: Lift the glove box and position it back into its original place. Push up on the glove box until it snaps into place.
-
Reset the Maintenance Reminder: If your vehicle is equipped with a maintenance reminder, reset it to ensure it accurately reflects the cabin air filter replacement.
| Recommended Cabin Air Filter Replacement Frequency |
|---|
| Every 12,000 to 15,000 miles or once a year (whichever comes first) |
How To Access Cabin Air 2008 Honda CR-V
To access the cabin air filter on a 2008 Honda CR-V, follow these steps:
1. Open the glove box and remove its contents.
2. Locate the two plastic tabs on the sides of the glove box opening.
3. Squeeze the tabs together and pull the glove box straight towards you to remove it.
4. The cabin air filter is located behind the glove box opening.
5. To remove the filter, simply pull it straight out.
6. Inspect the filter for dirt and debris. If the filter is dirty, replace it with a new one.
7. To install the new filter, simply slide it into the opening until it is flush with the edges.
8. Reinstall the glove box by aligning it with the opening and pushing it back into place.
People Also Ask About How To Access Cabin Air 2008 Honda CR-V
Where is the cabin air filter located on a 2008 Honda CR-V?
The cabin air filter on a 2008 Honda CR-V is located behind the glove box.
What is the purpose of the cabin air filter on a 2008 Honda CR-V?
The cabin air filter helps to remove dust, pollen, and other pollutants from the air that enters the passenger compartment of the vehicle.
How often should I replace the cabin air filter on my 2008 Honda CR-V?
Honda recommends that you replace the cabin air filter on your 2008 CR-V every 12,000 miles or 12 months, whichever comes first.
