If you’re like most people, you probably have a PopSocket on your phone. These handy little gadgets are a great way to keep your phone from slipping out of your hand, and they can also be used as a stand for watching videos or FaceTime. But what happens when your PopSocket falls off? Don’t worry, it’s easy to restick it. Here’s how.
The first step is to clean the surface of your phone where you want to restick the PopSocket. Use a rubbing alcohol wipe or a cotton ball dipped in rubbing alcohol to remove any dirt or oil. Once the surface is clean, peel off the backing of the PopSocket and press it firmly into place. Hold it for a few seconds to make sure it’s secure.
If you’re having trouble getting the PopSocket to stick, you can try using a hair dryer to heat up the adhesive. Just be careful not to hold the hair dryer too close to the PopSocket, or you could damage it. Once the adhesive is warm, press the PopSocket into place and hold it for a few seconds. It should now be securely attached to your phone.
Removing the Popsocket
Removing a Popsocket requires careful steps to avoid damaging the device or the surface it is attached to. Follow these detailed instructions to successfully detach the Popsocket:
1. Locate the Release Tab: Identify the small, grooved tab located on the base of the Popsocket. This is the key to releasing the grip.
a. Push and Slide: Press down firmly on the release tab with your thumb or finger. While applying pressure, gently slide the tab forward in the direction of the arrow.
b. Break the Grip: As you slide the tab, the Popsocket’s grip will begin to weaken. Continue sliding until the grip completely releases.
c. Lift the Popsocket: Once the grip is broken, carefully lift the Popsocket straight upwards from the surface. Avoid pulling it at an angle to prevent any damage.
2. Remove the Adhesive: If any adhesive residue remains on the surface, gently wipe it away with a soft cloth or a cotton swab dipped in rubbing alcohol.
3. Clean the Popsocket: To prepare the Popsocket for reattaching, clean the adhesive surface thoroughly with rubbing alcohol and a cotton swab. Allow it to air dry completely before reusing.
Preparing the Surface
Ensuring a clean and dry surface is crucial for successful Popsocket reattachment. This process can be broken down into three key steps:
Cleaning the Surface
Thoroughly clean the surface where the Popsocket will be reattached using a rubbing alcohol-based solution or a dedicated device cleaning wipe. This will remove any dirt, oil, or residue that could interfere with adhesion. Allow the surface to dry completely before proceeding.
Removing Existing Adhesive
If there is any remaining adhesive from the previous Popsocket, gently scrape it away using a plastic tool, such as a credit card or a guitar pick. Avoid using sharp objects that could damage the surface. If the adhesive is particularly stubborn, you can use a mild adhesive remover, but test it on an inconspicuous area first to ensure it does not damage the surface.
Applying Adhesive
If necessary, apply a thin layer of adhesive to the Popsocket. Avoid using excessive adhesive, as this can create a mess and reduce the bond’s strength. The type of adhesive used will depend on the material of the surface and the Popsocket. Consult the Popsocket manufacturer’s instructions for specific recommendations.
Applying Adhesive
Once you’ve removed the old adhesive, it’s time to apply new adhesive. Here are some tips:
**Choose the right adhesive.** Not all adhesives are created equal. For PopSockets, you’ll want to use a strong adhesive that will hold up to daily use. Some good options include Gorilla Glue Super Glue or Loctite Super Glue.
**Apply the adhesive sparingly.** A little bit of adhesive goes a long way. Too much adhesive can make a mess and weaken the bond.
**Use a toothpick or cotton swab to apply the adhesive.** This will help you get the adhesive into the small crevices of the PopSocket.
**Let the adhesive dry completely.** This may take several hours or overnight. Don’t try to use the PopSocket until the adhesive is completely dry.
**Here’s a step-by-step guide to applying adhesive to a PopSocket:**
| Step | Instructions |
|---|---|
| 1 | Remove the old adhesive from the PopSocket and phone case. |
| 2 | Choose the right adhesive and apply it sparingly to the PopSocket. |
| 3 | Use a toothpick or cotton swab to apply the adhesive into the small crevices of the PopSocket. Be sure to get the adhesive into the corners and edges. |
| 4 | Let the adhesive dry completely. This may take several hours or overnight. |
| 5 | Once the adhesive is dry, reattach the PopSocket to your phone case. |
Centering the Popsocket
To center the Popsocket, start by aligning the base of the Popsocket with the center of your phone or case. Use your finger or a tool to gently press down on the base of the Popsocket until it is firmly attached.
Next, use your fingertips to hold the Popsocket in place while you gently pull the top of the Popsocket towards the center of your phone or case. Continue pulling until the top of the Popsocket is aligned with the center of the base.
Finally, use your fingertips to gently press down on the top of the Popsocket until it is firmly attached. Check to make sure that the Popsocket is centered and secure before using it.
| Step | Instructions |
|---|---|
| 1 | Align the Popsocket’s base with the center of your phone or case. |
| 2 | Hold the Popsocket’s base in place and pull the top towards the center. |
| 3 | Press down on the top of the Popsocket until it’s secure and centered. |
Pressing Down
Once the adhesive is in place, it’s time to press down firmly on the PopSocket. Use your fingers to apply even pressure across the entire surface of the PopSocket, making sure that all edges are securely attached. Hold the pressure for at least 30 seconds to ensure that the adhesive has had enough time to bond with the surface.
To enhance the bond further, you can use a heavy object to weigh down the PopSocket while it dries. Place the object on top of the PopSocket and leave it there for several hours or overnight. This additional weight will help to press the PopSocket into the surface and create a stronger bond.
Once the adhesive has dried completely, your PopSocket will be securely attached to your device or case. You can now use it to hold your device, prop it up for hands-free viewing, or even wrap earbuds around it for tangle-free storage.
| Adhesive Type | Drying Time |
|---|---|
| 3M VHB Adhesive | 24 hours |
| Super Glue | 1 hour |
| Epoxy Resin | 2-3 days |
Curing the Adhesive
If the adhesive is still tacky, you can try to cure it by exposing it to air. Place the PopSocket on a flat surface with the adhesive side up. Leave it there for several hours, or even overnight, to allow the air to circulate and dry out the adhesive.
If the adhesive is not tacky, you can try to heat it up. Use a hair dryer on a low setting to warm the adhesive for a few minutes. This will soften the adhesive and make it more pliable.
Once the adhesive is heated, press the PopSocket firmly onto the back of your phone. Hold it in place for a few minutes to allow the adhesive to cool and bond with the phone.
Here are some additional tips for curing the adhesive:
- If the adhesive is still not sticking, you can try applying a small amount of super glue to the back of the PopSocket. Be careful not to use too much glue, as it can damage your phone.
- If you are having trouble getting the PopSocket to stick to a curved surface, you can try using a curved adhesive pad. These pads are designed to help PopSockets stick to curved surfaces, such as the back of an iPhone X.
- If you are still having trouble getting the PopSocket to stick, you can try contacting PopSockets customer service. They may be able to provide you with additional assistance.
Testing the Bond
Once you’ve cleaned both surfaces, it’s time to test the bond. To do this, simply apply a small amount of pressure to the PopSocket while it’s attached to your phone or case. If the PopSocket doesn’t budge, then the bond is strong and you’re good to go. However, if the PopSocket comes loose, then you’ll need to repeat the cleaning process and try again.
Here are some additional tips for testing the bond:
- Apply pressure to the PopSocket from different angles to make sure that the bond is secure all around.
- If the PopSocket is still coming loose, try using a stronger adhesive. Gorilla Glue is a good option for this.
- If you’re still having trouble getting the PopSocket to stick, you can try contacting the manufacturer for assistance.
Here is a table summarizing the different ways to test the bond of your PopSocket:
| Method | Description |
|---|---|
| Pressure test | Apply pressure to the PopSocket from different angles to make sure that the bond is secure all around. |
| Adhesive test | If the PopSocket is still coming loose, try using a stronger adhesive. Gorilla Glue is a good option for this. |
| Manufacturer contact | If you’re still having trouble getting the PopSocket to stick, you can try contacting the manufacturer for assistance. |
Troubleshooting Loose Popsockets
If your Popsocket is feeling loose, there are a few things you can do to try to fix it.
1. Check the adhesive
The first thing to check is the adhesive on the back of the Popsocket. If it’s dirty or damaged, it may not be able to hold the Popsocket in place. To clean the adhesive, use a cotton swab dipped in rubbing alcohol. Be careful not to get any rubbing alcohol on the Popsocket itself, as it could damage the finish.
2. Warm up the adhesive
If the adhesive is cold, it may not be able to hold the Popsocket in place. To warm up the adhesive, use a hair dryer on the low setting. Hold the hair dryer about 6 inches away from the Popsocket and blow hot air on it for about 30 seconds.
3. Apply pressure
Once the adhesive is warm, apply pressure to the Popsocket to help it stick. You can do this by pressing on the Popsocket with your thumb for about 30 seconds.
4. Let the adhesive dry
Once you’ve applied pressure to the Popsocket, let the adhesive dry completely. This may take several hours.
5. Try a different surface
If the adhesive still isn’t holding the Popsocket in place, try sticking it to a different surface. Some surfaces, such as silicone or rubber, may not be compatible with the adhesive on the Popsocket.
6. Use a Popsocket mount
If you’re having trouble getting the Popsocket to stick to your phone, you can try using a Popsocket mount. Popsocket mounts are designed to hold Popsockets in place on a variety of surfaces.
7. Contact Popsocket
If you’ve tried all of the above troubleshooting tips and your Popsocket is still loose, you can contact Popsocket for help. Popsocket offers a warranty on its products, and they may be able to replace your Popsocket if it’s defective.
8. Relocate the Popsocket to strengthen its grip:
Identify a location on the phone’s surface that offers a wider, flatter area, allowing for more adhesive contact. This could be the center of the phone’s back panel or a location with a smooth, non-textured surface.
Before relocating the Popsocket, thoroughly clean both the phone’s surface and the Popsocket’s base with rubbing alcohol. Allow both surfaces to dry completely before proceeding.
Peel off the Popsocket’s base from its current location and align it with the new location you’ve identified. Press down firmly for several seconds, ensuring there are no air bubbles trapped beneath the adhesive.
Leave the Popsocket undisturbed for at least 24 hours to allow the adhesive to fully cure and bond with the phone’s surface. This extended curing time will significantly enhance the Popsocket’s grip.
| Problem | Solution |
|---|---|
| Popsocket keeps falling off | Clean the adhesive on the back of the Popsocket and the surface of your phone. Apply pressure to the Popsocket to help it stick. |
| Popsocket is loose | Warm up the adhesive on the back of the Popsocket with a hair dryer. Apply pressure to the Popsocket to help it stick. |
| Popsocket won’t stick to my phone | Try using a Popsocket mount. Popsocket mounts are designed to hold Popsockets in place on a variety of surfaces. |
Tips for Better Adhesion
Here are some tips to help you get the best adhesion from your PopSocket:
1. Clean the Surface
Make sure the surface of your phone or case is clean and dry before applying the PopSocket. This will help to remove any dirt or oils that could prevent the adhesive from sticking properly.
2. Use a Hair Dryer
Heat can help to activate the adhesive on the PopSocket. Use a hair dryer to warm up the adhesive for 30 seconds before applying it to your phone.
3. Press Firmly
Once you have applied the PopSocket to your phone, press down firmly for 30 seconds. This will help to ensure that the adhesive bonds properly.
4. Avoid Using the PopSocket Immediately
Allow the adhesive to cure for 24 hours before using the PopSocket. This will give the adhesive time to set properly.
5. Don’t Overuse the PopSocket
The PopSocket is designed to be used as a temporary stand or grip. Avoid putting too much weight on it, as this could cause the adhesive to fail.
6. Remove the PopSocket Carefully
If you need to remove the PopSocket, do so carefully. Peel the PopSocket off slowly and gently, being careful not to damage the adhesive.
7. Use a PopSocket Mount
If you want to use your PopSocket in your car or on your desk, consider using a PopSocket mount. A mount will help to keep your phone secure and in place.
8. Replace the Adhesive
The adhesive on your PopSocket will eventually wear out. If you find that your PopSocket is no longer sticking properly, you can replace the adhesive with a new one.
9. Troubleshooting Adhesive Problems
If you are having trouble getting your PopSocket to stick, there are a few things you can try:
| Problem | Solution |
|---|---|
| The PopSocket is not sticking to my phone | Make sure the surface of your phone is clean and dry. You can also try using a hair dryer to warm up the adhesive. |
| The PopSocket is falling off my phone | Press down firmly on the PopSocket for 30 seconds to ensure that the adhesive bonds properly. Avoid overusing the PopSocket and remove it carefully when not in use. |
| The adhesive on my PopSocket is damaged | Replace the adhesive with a new one. |
Cleaning a Popsocket
Before you can restick your Popsocket, it must be cleaned. Here are the steps on how to clean your Popsocket:
- Locate a flat surface that is clean and dry.
- Place the Popsocket on the flat surface with the adhesive side facing up.
- Pour a small amount of isopropyl alcohol (rubbing alcohol) onto a cotton ball or swab.
- Gently rub the cotton ball or swab over the adhesive surface of the Popsocket in circular motions.
- Use a clean cotton ball or swab to wipe away any remaining alcohol and dirt.
- Allow the Popsocket to air dry completely before applying any new adhesive.
Additional Tips for Cleaning a Popsocket
Here are some additional tips for cleaning your Popsocket:
- Do not use any harsh chemicals or cleaners to clean your Popsocket, as these could damage the adhesive.
- If the adhesive on your Popsocket is particularly dirty or sticky, you may need to soak it in isopropyl alcohol for a few minutes before wiping it clean.
- Once your Popsocket is clean and dry, you can apply a new layer of adhesive to it and reattach it to your device.
| Cleaning Solution | Caution |
|---|---|
| Water | May not be effective against all types of dirt and grime. |
| Isopropyl alcohol (rubbing alcohol) | Can be harsh on the adhesive, so use sparingly. |
| WD-40 | Can damage the adhesive if not used properly. |
How To Restick A Popsocket
If your PopSocket has come loose, don’t worry! It’s easy to restick it. Here’s how:
- Clean the surface of your device. Use a rubbing alcohol wipe or a cotton ball dipped in rubbing alcohol to clean the surface where you want to restick the PopSocket. This will remove any dirt or oil that could prevent the PopSocket from sticking.
- Remove the old adhesive from the PopSocket. Use your fingernail or a sharp object to carefully remove the old adhesive from the back of the PopSocket. Be careful not to damage the PopSocket.
- Apply new adhesive to the PopSocket. Use a small amount of super glue or epoxy to apply a thin layer of adhesive to the back of the PopSocket. Be careful not to use too much adhesive, or it will ooze out and make a mess.
- Restick the PopSocket to your device. Press the PopSocket firmly into place on your device. Hold it in place for a few seconds to allow the adhesive to set.
People Also Ask About How To Restick A Popsocket
How do you restick a PopSocket without glue?
There are a few ways to restick a PopSocket without glue. One way is to use a double-sided adhesive tape. Cut a small piece of tape and apply it to the back of the PopSocket. Then, press the PopSocket firmly into place on your device.
Another way to restick a PopSocket without glue is to use a hair dryer. Heat the adhesive on the back of the PopSocket with a hair dryer until it becomes soft. Then, press the PopSocket firmly into place on your device.
How do you fix a sticky PopSocket?
If your PopSocket is sticky, you can try cleaning it with a rubbing alcohol wipe. Rub the wipe over the sticky surface until it is no longer sticky. You can also try using a cotton ball dipped in rubbing alcohol.
How do you remove a PopSocket without damaging the phone?
To remove a PopSocket without damaging your phone, use a credit card or a sharp object to carefully pry the PopSocket off of your phone. Be careful not to damage the phone or the PopSocket.
