Nail clippers are an essential grooming tool, but they can be frustrating to use when they come apart. If your nail clippers have come apart, don’t worry – it’s easy to put them back together. By following a few simple steps, you can have your nail clippers working again in no time.
First, identify the pieces of your nail clippers. There should be a top half and a bottom half, as well as a spring and a lever. The spring is what holds the two halves of the nail clippers together, while the lever is what you use to cut your nails. Once you’ve identified the pieces, you need to find the hole in the bottom half of the nail clippers. This hole is where the spring will go.
Next, insert the spring into the hole. The spring should be inserted so that the coils are facing down. Once the spring is in place, you need to put the top half of the nail clippers back on. The top half should fit snugly over the bottom half, and the spring will keep the two halves together. Finally, you need to insert the lever. The lever should fit into the slot on the top half of the nail clippers. Once the lever is in place, your nail clippers are ready to use.
Disassembling the Nail Clipper
To disassemble the clipper, you’ll need:
- A thin object like a flat-head screwdriver or a safety pin
- A strong pair of pliers
- A small bowl or dish
1. Removing the Lever
– Start by prying the lever away from the body of the clipper with the thin object. Be careful not to damage the lever or the clipper.
– Once the lever is loose, use the pliers to gently pull it away from the clipper.
– Set the lever aside in the small bowl or dish.
2. Removing the Spring
– Once the lever is removed, you’ll see the spring that attaches the lever to the clipper.
– Use the pliers to gently squeeze the spring until it pops out of its slot.
– Set the spring aside in the bowl or dish.
|
**Tip:** It’s helpful to have a small bowl or dish to keep track of the small parts as you disassemble the clipper. |
Removing the Broken Blade
Removing the broken blade from a nail clipper requires careful handling to avoid further damage. Here are the steps to follow:
Hold the nail clipper securely.
Use your fingers to grip the outer arms of the nail clipper, making sure to hold it steady.
Locate the pivot screw.
Most nail clippers have a single pivot screw that holds the blades together. Identify the screw on the side of the clipper and gently loosen it with a screwdriver.
Lift the top blade.
Once the pivot screw is loosened, carefully lift the top blade away from the bottom blade. Use a pair of tweezers or needle-nosed pliers to gently grasp the blade at the pivot point and pull it upward.
Remove the broken blade.
Once the top blade is lifted, the broken blade will be exposed. Carefully remove the broken blade and discard it.
Inserting the New Blade
To insert the new blade, first, open the nail clippers as far as they will go. Next, locate the small screw or hinge pin that holds the two halves of the clippers together. Using a small screwdriver or a pair of pliers, loosen the screw or remove the pin.
Once the screw or pin is loose, carefully separate the two halves of the clippers. Be careful not to lose the small springs or washers that may be inside. Place the new blade in the correct position, aligning it with the holes or slots in the clipper body.
Reassemble the clippers by aligning the two halves and inserting the screw or pin. Tighten the screw or insert the pin until the clippers are securely closed. Test the clippers to make sure they are cutting properly.
| Tools Needed |
|---|
| Small screwdriver or pliers |
Aligning the Jaws
To realign the jaws of the nail clipper, there are a few steps you’ll need to follow:
- Identify the pivot point: Locate the small pin or screw that connects the two sides of the clipper. This is the pivot point.
- Open the clipper slightly: With one hand, hold the handle of the clipper and open it slightly. This will create a gap between the jaws.
- Insert a thin tool: Using a small, thin tool like a toothpick or needle, insert it into the gap between the jaws. Gently slide the tool back and forth to loosen any debris or stuck particles.
- Realign the jaws: Once the jaws are loose, you can carefully align them by pushing them together with your fingers. Make sure the blades meet evenly on both sides.
- Tighten the screw: Once the jaws are aligned, tighten the screw or pin that connects them. This will secure the jaws in place.
Here’s an additional table summarizing the steps involved in aligning the jaws of a nail clipper:
| Step | Action |
|---|---|
| 1 | Identify the pivot point. |
| 2 | Open the clipper slightly. |
| 3 | Insert a thin tool into the gap between the jaws. |
| 4 | Realign the jaws and tighten the screw. |
Tightening the Screw
Once you’ve cleaned and lubricated the nail clipper, it’s time to put it back together. Start by placing the screw back into the hole on the top of the clipper.
Next, use a screwdriver to tighten the screw. Be careful not to overtighten the screw, as this can damage the clipper.
Once the screw is tightened, test the clipper to make sure it’s working properly. If the clipper is still not cutting properly, you may need to adjust the tension of the spring.
Adjusting the Tension of the Spring
If the nail clipper is not cutting properly, you may need to adjust the tension of the spring. To do this, locate the spring on the inside of the clipper.
Use a pair of pliers to gently bend the spring. Bending the spring inward will increase the tension, while bending the spring outward will decrease the tension.
Once you’ve adjusted the tension of the spring, test the clipper to make sure it’s working properly.
| Tool | Description |
|---|---|
| Screwdriver | Phillips’ or flat head, depends on your clipper |
| Pliers | Needle-nose pliers are recommended |
Reattaching the Lever
6. Realigning the Pinion Gear
The pinion gear is a small, notched wheel that connects the lever to the cutting mechanism. To realign it:
| Step | Instructions |
|---|---|
| a | Hold the lever upside down and insert the pinion gear into the hole on the underside of the lever. |
| b | Make sure the notches in the pinion gear face the same direction as the notches in the cutting mechanism. |
| c | Gently push on the pinion gear until it snaps into place. |
| d | Test the lever by squeezing it. The cutting mechanism should move smoothly up and down. |
If the lever is still not working properly, repeat steps a-c and make sure the pinion gear is securely aligned.
Adjusting the Tension
Once you have reassembled the nail clipper, you may need to adjust the tension to ensure it cuts smoothly. Here are the steps on how to adjust the tension:
1. Hold the nail clipper in one hand and the adjustment screw in the other.
2. Turn the adjustment screw clockwise to tighten the tension or counterclockwise to loosen it.
3. Test the tension by cutting a piece of nail. If the tension is too tight, the clipper will crush the nail; if it is too loose, the clipper will not cut cleanly.
4. Continue adjusting the tension until you find the right balance where the clipper cuts smoothly without crushing or tearing the nail.
5. Once you have found the correct tension, tighten the adjustment screw securely to prevent it from loosening.
Tips for Adjusting the Tension
Here are a few tips to help you adjust the tension on your nail clipper:
- Start with the tension set to the middle position and adjust it from there.
- Make small adjustments to the tension and test the clipper after each adjustment.
- If you are having trouble adjusting the tension, consult the manufacturer’s instructions.
Testing the Nail Clipper
Once you’ve reassembled the nail clipper, it’s crucial to test it to ensure it functions correctly.
1. Close the Nail Clipper: Shut the nail clipper completely to check if it closes smoothly and aligns properly.
2. Check for Sharpness: Trim a piece of paper to verify the sharpness of the blades. The clipper should cut through the paper cleanly and effortlessly.
3. Test the Spring: Open and close the nail clipper several times to assess the spring’s functionality. It should create sufficient tension to open and close the clippers with ease.
4. Adjust the Tension: If the spring is too loose or too tight, you can adjust its tension by tightening or loosening the screw that secures it. Experiment until you find the desired tension.
5. Test on Nails: Finally, try trimming your nails with the repaired nail clipper. Check if it cuts smoothly and doesn’t leave any jagged edges. If necessary, make further adjustments to the tension or sharpness until you’re satisfied with the performance.
Troubleshooting Tips:
If the Nail Clipper Doesn’t Cut Properly:
| Possible Cause | Solution |
|---|---|
| Dull blades | Sharpen the blades or replace them |
| Misalignment | Check and adjust the alignment of the blades |
| Loose spring | Tighten the spring screw |
If the Nail Clipper Doesn’t Close Properly:
| Possible Cause | Solution |
|---|---|
| Obstruction | Remove any debris or dirt blocking the closure |
| Misalignment | Check and adjust the alignment of the handles |
| Weak spring | Replace the spring |
Proper Maintenance and Storage
Cleaning
Regularly clean your nail clippers using a brush or cotton swab dipped in rubbing alcohol. This will remove dirt, grime, and bacteria that can accumulate over time.
Lubrication
Apply a small drop of oil to the blades and moving parts to ensure smooth operation. Use a lubricant specifically designed for metal tools.
Sharpening
Sharpen the blades periodically using a nail file or sharpening stone. Hold the file or stone at a 45-degree angle to the blade and gently slide it along the edge.
9. Proper Storage
Store your nail clippers in a dry, clean place to prevent rust and corrosion. Here are some specific tips for proper storage:
| Storage Method | Benefits |
|---|---|
| Closed Case or Box | Protects from dust, moisture, and accidental damage |
| Hanging on a Hook | Prevents moisture accumulation and allows for easy access |
| Magnetic Holder | Keeps clippers securely in place while maintaining proper alignment |
Avoid storing your nail clippers in humid environments or in contact with other metal objects, as this can lead to rust.
Troubleshooting Common Issues
1. The Nail Clipper is Not Cutting Properly
The blades may be dull. Try sharpening them with a nail file or sandpaper.
2. The Nail Clipper is Jammed
The nail clippings may be stuck in the clipper. Remove them with a pair of tweezers.
3. The Spring is Broken
The spring is essential for the clipper to work properly. If it is broken, replace it with a new one.
4. The Handle is Loose
The handle may be loose if the screws are not tightened properly. Tighten the screws with a screwdriver.
5. The Nail Clipper is Rusting
The clipper may rust if it is not properly cleaned and dried after use. Wipe it down with a damp cloth and dry it with a towel.
6. The Nail Clipper is Made of Cheap Material
The cheaper the clipper, the more likely it will break. If you want a durable clipper, invest in a well-made one.
7. You Are Not Using the Clipper Properly
Make sure you are using the clipper correctly. Hold it at a 90-degree angle to your nail and squeeze the handles.
8. Your Nails Are Too Thick
If your nails are thick, you may need to use a pair of heavy-duty clippers.
9. You Need to Trim Your Nails Regularly
Regular trimming will help prevent your nails from becoming too long and thick.
10. The Nail Clipper Has a Design Flaw
Some nail clippers are simply poorly designed. If your clipper has a design flaw, you may not be able to fix it.
If you have tried all of the troubleshooting tips above and your nail clipper is still not working properly, you may need to purchase a new one.
How to Put a Nail Clipper Back Together
Nail clippers are one of those everyday objects that we often take for granted. But when they break, it can be a real pain to try to put them back together. If you’ve ever found yourself in this situation, don’t worry! Here are some simple steps on how to put a nail clipper back together:
- Find the two main pieces of the nail clipper. These two pieces should be easy to identify, as they will be the largest pieces of the clipper.
- Find the spring. The spring is a small, metal piece that is responsible for making the nail clipper open and close. It will usually be located in the center of the nail clipper.
- Insert the spring into the nail clipper. To do this, you will need to use a small screwdriver or a pair of pliers. Once the spring is in place, it should snap into place.
- Put the two main pieces of the nail clipper back together. To do this, you will need to align the two pieces and then press them together. You may need to use a little bit of force to do this.
- Test the nail clipper. Once the nail clipper is back together, you should test it to make sure that it is working properly. To do this, simply try to cut a nail.
People Also Ask About How to Put a Nail Clipper Back Together
How do I fix a nail clipper that won’t open?
If your nail clipper won’t open, it is likely that the spring is broken. To fix this, you will need to replace the spring. You can purchase a new spring at most hardware stores.
How do I sharpen a nail clipper?
To sharpen a nail clipper, you can use a whetstone or a fine-grit sandpaper. To do this, simply hold the nail clipper against the whetstone or sandpaper and move it back and forth until the blades are sharp.
How do I clean a nail clipper?
To clean a nail clipper, you can use rubbing alcohol or a disinfectant spray. To do this, simply apply the cleaning solution to the nail clipper and then wipe it off with a clean cloth.
