Sustaining a clear and wholesome pool ensures each your enjoyment and the longevity of your funding. A vital side of pool upkeep is commonly backwashing your filter. Backwashing removes amassed grime, particles, and contaminants from the filter media, permitting it to perform successfully and preserve your pool water glowing clear. The Hayward pool filter is famend for its effectivity and reliability, and backwashing this filter is an easy but important process that each pool proprietor ought to grasp. So, dive into this complete information on the right way to backwash your Hayward pool filter and guarantee a crystal-clear swimming expertise all season lengthy.
Earlier than embarking on the backwashing course of, it is vital to organize your filter and gear. Make sure that the pump is turned off, and the system is pressurized. Find the backwash valve, which is usually a multi-port valve located on high of the filter. The valve has totally different settings, together with “filter,” “backwash,” “rinse,” and “closed.” To provoke backwashing, flip the valve to the “backwash” place. This motion reverses the circulate of water via the filter, forcing the amassed particles out of the media and into the waste line. Enable the filter to backwash for a couple of minutes, or till the sight glass on the filter signifies that the water runs clear.
As soon as the backwashing course of is full, it is time to rinse the filter media. Flip the multi-port valve to the “rinse” place, which permits clear water to circulate via the filter within the regular path. This step helps to take away any remaining particles and ensures that the filter is totally cleaned. Rinse the filter for a couple of minutes, or till the sight glass signifies clear water. Lastly, flip the valve again to the “filter” place to renew regular filtration.
Gathering Essential Instruments and Supplies
Earlier than embarking on the backwashing course of, it’s essential to collect all the required instruments and supplies to make sure a clean and environment friendly operation. Listed below are the important gadgets you may want:
Multiport Valve Key
The multiport valve key’s a specialised instrument that matches into the valve’s slots and permits you to rotate it to totally different positions. It is vital to make use of the right key to keep away from damaging the valve.
Hose or Drain Line
A backyard hose or drain line is required to direct the backwash water away from the pool and into a delegated space, equivalent to a drain or sewer.
Stress Gauge
A stress gauge helps you monitor the filter’s stress earlier than, throughout, and after backwashing. It could possibly point out when the filter wants cleansing.
Pool Pump Primer
If utilizing a self-priming pump, a primer instrument could also be essential to fill the pump with water earlier than beginning it up.
Water Check Equipment
A water take a look at equipment permits you to verify the pool water’s chemical steadiness. That is really useful after backwashing to make sure the water chemistry is inside optimum ranges.
Different Useful Gadgets
Along with the important instruments and supplies, take into account having the next gadgets available:
| Merchandise | Function |
|---|---|
| Fabric or rag | To wash any water spills across the filter |
| Gloves | To guard your arms from water and chemical substances |
| Security glasses | To guard your eyes from splashes |
Cleansing the Filter Parts
This course of requires cautious removing of the filter parts for thorough cleansing. Observe these steps:
1. Take away the Filter Parts
Flip off the pool pump and relieve the stress within the filter by opening the air launch valve positioned on high of the filter. Loosen the filter clamp or lid and thoroughly take away the filter parts (normally cartridge or D.E. grids).
2. Rinse with Backyard Hose
Maintain the filter parts upright and rinse them totally with a robust stream of water from a backyard hose. Use a nozzle with a high-pressure spray to dislodge any grime, particles, or algae.
3. Deep Clear (Chemical Soak)
For Cartridge Filters:
Fill a big bucket or tub with water and add a specialised cartridge filter cleaner. Immerse the cartridge parts within the resolution and allow them to soak for the really useful length (sometimes 12-24 hours). This chemical soak helps dissolve and eradicate cussed contaminants.
| Step | Description |
|---|---|
| 1 | Fill a bucket or tub with water and add cartridge filter cleaner. |
| 2 | Immerse cartridge parts within the resolution. |
| 3 | Let soak for 12-24 hours. |
For D.E. (Diatomaceous Earth) Grids:
Rinse the D.E. grids totally with water after which use a light detergent resolution (1 cup of detergent per gallon of water) for a deep clear. Soak the grids within the resolution for 1 hour, then rinse once more to take away any remaining residue.
| Step | Description |
|---|---|
| 1 | Rinse D.E. grids with water. |
| 2 | Put together a detergent resolution (1 cup per gallon). |
| 3 | Soak grids for 1 hour. |
| 4 | Rinse grids once more. |
Monitoring the Backwashing Course of
Keep watch over the next parameters in the course of the backwashing course of to make sure its effectiveness:
1. Length
Examine the sight glass for 1-2 minutes. If the water stays cloudy, proceed backwashing.
2. Readability
Examine the sight glass to substantiate if the water has change into clear. If it hasn’t, lengthen the backwashing time.
3. Stress Gauge
Be aware the stress drop on the filter’s stress gauge. As soon as it reaches regular ranges, cease backwashing.
4. Time Counter (Non-obligatory)
In case your filter has a time counter, it’s going to point out the time remaining for the backwash cycle. Monitor it accordingly.
5. Circulation Charge
Guarantee that there’s a sturdy circulate price throughout backwashing. Whether it is weak or absent, verify for any blockages.
6. Sight Glass Remark
After the preliminary cloudy water discharge, observe the sight glass:
| Stage | Sight Glass Look |
|---|---|
| Preliminary Section | Darkish, cloudy water |
| Transition | Brownish, murky water |
| Clear Water | Clear, glowing water |
Cease backwashing when the sight glass exhibits clear water.
Troubleshooting Backwashing Points
Air within the Filter Tank
In case your filter just isn’t backwashing correctly, it might be as a consequence of air within the filter tank. To resolve this challenge, attempt opening the air aid valve on high of the filter and operating the backwash cycle till all the air is eliminated.
Clogged Filter Media
If the filter media is clogged, it is not going to permit water to circulate via the filter correctly. To wash the filter media, take away the filter cartridges and clear them with a hose or a filter cleaner. Change the filter cartridges and backwash the filter once more.
Damaged Backwash Valve
If the backwash valve is damaged, it won’t be able to modify the filter from filtration mode to backwash mode. To restore the backwash valve, you will have to switch the valve or the complete filter head.
Leaking Backwash Line
If the backwash line is leaking, it’s going to stop water from flowing out of the filter in the course of the backwash cycle. To repair the leaking backwash line, examine the road for any holes or cracks and restore them as wanted.
Clogged Drain Line
If the drain line is clogged, it’s going to stop water from draining out of the filter in the course of the backwash cycle. To wash the drain line, disconnect the road from the filter and clear any particles that could be blocking it.
Incorrect Timer Setting
If the timer just isn’t set appropriately, the filter is not going to backwash on time. To regulate the timer, seek advice from the producer’s directions in your particular filter mannequin.
Low Water Degree
If the water degree within the pool is simply too low, the filter won’t be able to backwash correctly. To resolve this challenge, add water to the pool till it reaches the correct degree.
Defective Pump
If the pump just isn’t working correctly, it won’t be able to supply the required water stress to backwash the filter. To resolve this challenge, examine the pump for any injury and restore or change the pump as wanted
Learn how to Backwash Hayward Pool Filter
Backwashing a Hayward pool filter is a crucial a part of common pool upkeep that removes grime and particles from the filter media. By preserving your filter clear, you may assist it run extra effectively and lengthen its life.
Step 1: Flip off the pump
Step one is to show off the pool pump. This can stop water from flowing via the filter when you are backwashing it.
Step 2: Set the valve to “Backwash”
Find the valve on the highest of the filter and switch it to the “Backwash” setting. This can permit water to circulate backward via the filter, which is able to assist to dislodge grime and particles from the filter media.
Step 3: Backwash for 2-3 minutes
Enable the filter to backwash for 2-3 minutes, or till the water runs clear. Chances are you’ll must backwash for longer in case your filter is closely soiled.
Step 4: Flip off the valve and rinse the filter
As soon as the water is evident, flip the valve again to the “Filter” setting. Enable the filter to rinse for a couple of seconds to take away any remaining particles.
Step 5: Activate the pump
Lastly, flip the pool pump again on and permit the filter to run usually. Your filter is now clear and able to use.
Individuals Additionally Ask About Learn how to Backwash Hayward Pool Filter
How typically ought to I backwash my Hayward pool filter?
It’s best to backwash your Hayward pool filter as soon as each 2-3 weeks in summer season. Nonetheless, you may backwash it roughly incessantly relying on how soiled your pool water is.
What if my Hayward pool filter will get clogged?
In case your Hayward pool filter will get clogged, you will have to scrub it instantly. You’ll know if the filter is clogged when the water stress is low, the pool water is cloudy, and the filter is making uncommon noises.
