Are you bored with having to change between the bathe and bathtub manually? A diverter valve might help! This useful machine permits you to simply change the stream of water from the showerhead to the bathtub spout, and vice versa. Putting in a diverter valve is a comparatively easy undertaking that may be accomplished in just a few hours. Here is a step-by-step information that will help you get began.
Earlier than you start, you may want to assemble just a few instruments and supplies. You may want a diverter valve (accessible at most {hardware} shops), a wrench, a screwdriver, and a few Teflon tape. After getting the whole lot you want, you can begin the set up course of. Step one is to close off the water provide to your bathe. Subsequent, take away the showerhead by unscrewing it from the bathe arm. As soon as the showerhead is eliminated, you may have to take away the outdated diverter valve. To do that, merely unscrew the valve from the bathe arm. Now, you are prepared to put in the brand new diverter valve. Begin by wrapping the threads of the valve with Teflon tape, then screw the valve onto the bathe arm.
As soon as the diverter valve is put in, you may reattach the showerhead. Activate the water provide to your bathe, and test for leaks. If there are not any leaks, you are all set! Now you can benefit from the comfort of a diverter valve in your bathe.
Putting in the New Diverter Valve
1. Take away the Outdated Diverter Valve
Find the screws holding the outdated diverter valve in place and take away them. Gently pull the valve away from the pipe, taking care to not injury the threads.
2. Test the Threads
Examine the threads on the pipe and the brand new diverter valve. Be sure that they’re clear and freed from particles. If mandatory, use a thread cleaner to take away any burrs or corrosion.
3. Apply Sealant
Apply a skinny layer of sealant to the threads of the brand new diverter valve. This can assist create a watertight seal.
4. Set up the Diverter Valve
Thread the brand new diverter valve onto the pipe by hand, making certain it’s aligned accurately. Tighten it additional utilizing a wrench, being cautious to not overtighten.
5. Set up the Deal with
Find the deal with on the brand new diverter valve and align it with the slot on the valve physique. Slide the deal with onto the valve and safe it by tightening the screw.
6. Reattach the Escutcheon
Take the escutcheon (the ornamental plate surrounding the valve) and align it over the valve physique. Safe it by tightening the screws. Be sure that the escutcheon matches snugly towards the wall.
Further Particulars for Step 6:
– If the escutcheon doesn’t match flush towards the wall, you could want to make use of a spacer or washer to create a greater match.
– When tightening the escutcheon screws, keep away from overtightening, as this could injury the plate or the wall.
– If the escutcheon has a number of screws, tighten them in a star sample to make sure even strain distribution.
– As soon as the escutcheon is safe, test for any gaps or leaks across the edge. If mandatory, apply further sealant to seal any leaks.
Testing the Diverter Valve for Leaks
As soon as the diverter valve is put in, it is vital to check it for leaks. This can be certain that the valve is functioning correctly and that there are not any water leaks.
To check the diverter valve for leaks, comply with these steps:
1. Activate the water provide to the bathe or tub.
2. Open the bathe or tub faucet and let the water run for a couple of minutes.
3. Test for any leaks across the diverter valve. If there are any leaks, tighten the packing nut or change the O-ring.
4. Repeat steps 1-3 for the bathtub spout.
5. Flip off the water provide to the bathe or tub.
6. Test for any leaks across the diverter valve. If there are any leaks, tighten the packing nut or change the O-ring.
7. If there are not any leaks, the diverter valve is put in and functioning correctly.
8. If you’re nonetheless experiencing leaks after following these steps, there could also be an issue with the diverter valve itself. On this case, you will want to switch the diverter valve.
| Leak Location | Potential Trigger | Answer |
|---|---|---|
| Across the diverter valve deal with | Unfastened packing nut | Tighten the packing nut |
| Across the diverter valve physique | Broken O-ring | Exchange the O-ring |
| Across the bathe or tub spout | Unfastened connection | Tighten the connection |
How you can Match a Diverter Valve
A diverter valve is a plumbing fixture that permits you to management the stream of water between two completely different retailers. This may be helpful for quite a lot of functions, comparable to diverting water from a showerhead to a tub spout, or from a kitchen sink to a dishwasher. Diverter valves are comparatively simple to put in, and could be completed in just a few easy steps.
Step 1: Collect your supplies.
You will want the next supplies to put in a diverter valve:
- Diverter valve
- Wrench
- Plumber’s tape
- Screwdriver
Step 2: Flip off the water provide.
Earlier than you start engaged on the diverter valve, it is very important flip off the water provide to the fixture. This may be completed by turning off the principle water valve to your dwelling, or by turning off the person water valve for the fixture.
Step 3: Take away the outdated diverter valve.
As soon as the water provide is turned off, you may take away the outdated diverter valve. To do that, merely use a wrench to unscrew the nuts that maintain the valve in place. As soon as the nuts are unfastened, you may pull the valve off of the pipe.
Step 4: Set up the brand new diverter valve.
To put in the brand new diverter valve, merely reverse the steps that you simply used to take away the outdated valve. First, apply a small quantity of plumber’s tape to the threads of the valve. Then, screw the valve onto the pipe. Lastly, tighten the nuts that maintain the valve in place.
Step 5: Activate the water provide.
As soon as the diverter valve is put in, you may activate the water provide. Test for leaks across the valve, and tighten the nuts as mandatory.
Step 6: Take a look at the diverter valve.
To check the diverter valve, merely activate the water and test to make it possible for the water is flowing to the right outlet. If the water just isn’t flowing to the right outlet, you could want to regulate the place of the valve.
Individuals Additionally Ask
How do I do know if I would like a diverter valve?
You might want a diverter valve if you wish to management the stream of water between two completely different retailers. For instance, you could want a diverter valve if you wish to divert water from a showerhead to a tub spout, or from a kitchen sink to a dishwasher.
What are the several types of diverter valves?
There are two predominant kinds of diverter valves: push-pull diverter valves and lever diverter valves. Push-pull diverter valves are operated by pushing or pulling on a knob, whereas lever diverter valves are operated by transferring a lever up or down.
How do I select the correct diverter valve?
When selecting a diverter valve, you have to contemplate the next components:
- The kind of fixture you might be putting in the valve on
- The variety of retailers you wish to management
- The stream charge of the water
- The fashion of the valve
- The worth of the valve
