When your dryer stops tumbling or starts making a strange noise, it can be a frustrating experience. One potential cause of these issues is a malfunctioning reversal rotation motor. This motor is responsible for rotating the dryer drum in both directions, which helps to evenly distribute the clothes and prevent them from getting tangled. If the motor fails, the dryer will not be able to tumble properly, and your clothes will not dry evenly. In this article, we will provide step-by-step instructions on how to override a reversal rotation motor on a dryer. By following these instructions, you can get your dryer up and running again in no time.
Before you begin, it is important to note that overriding the reversal rotation motor will void the warranty on your dryer. If your dryer is still under warranty, it is best to contact the manufacturer for repairs. However, if your dryer is out of warranty or you are comfortable performing the repair yourself, then you can follow the steps below.
To override the reversal rotation motor, you will need to access the motor’s control board. The control board is typically located on the back of the dryer, behind the access panel. Once you have accessed the control board, you will need to locate the wires that connect to the reversal rotation motor. These wires are typically color-coded, so you should be able to easily identify them. Once you have identified the wires, you will need to disconnect them from the control board. Once the wires are disconnected, the reversal rotation motor will be overridden, and the dryer will be able to tumble in both directions again.
Identifying the Reversal Rotation Motor
The reversal rotation motor, also called the drive motor, is a crucial component in a dryer that allows the drum to rotate in both clockwise and counterclockwise directions. This alternating rotation helps prevent laundry from tangling and promotes even drying. Identifying the reversal rotation motor is essential for troubleshooting and servicing the dryer.
1. Locate the Motor Housing
Begin by inspecting the dryer’s back panel. Locate the large, cylindrical housing that houses the motor. It is typically secured by several bolts or screws. Carefully remove the housing to access the motor.
2. Identify the Motor Model and Part Number
Once the motor housing is removed, you will see the motor itself. On the motor’s exterior, there should be a label or a stamped metal plate indicating the model and part number. Note this information, as it will be helpful for ordering a replacement motor.
3. Check the Motor Shaft
The motor shaft is the rotating part that drives the drum. Inspect the shaft for any bends, cracks, or damage. Also, try rotating the shaft by hand. It should move smoothly and without resistance.
4. Examine the Wiring Connections
The reversal rotation motor typically has several wires connected to it. These wires provide power and control to the motor. Carefully disconnect the wires and examine them for any damage or loose connections. Loose or damaged wires can cause the motor to malfunction.
5. Test the Motor
To test the motor, you can use a multimeter to check for continuity and proper voltage. Refer to the manufacturer’s specifications for the correct voltage and testing procedures.
Accessing the Reversal Rotation Motor
1. Disconnect the Dryer from Power:
Unplug the dryer or turn off the circuit breaker that supplies power to it for safety.
2. Remove the Back Panel:
Locate the screws holding the back panel of the dryer in place. Remove the screws and carefully pull the panel away from the dryer.
3. Access the Reversal Rotation Motor:
Once the back panel is removed, you should have access to the reversal rotation motor. It is typically located near the center of the dryer’s back, behind the drum or blower wheel.
4. Identifying the Motor Terminals:
Reversal Rotation Motor Terminals:
Reversal rotation motors usually have three terminals. These terminals are typically color-coded as follows:
| Terminal Color | Connection |
|---|---|
| Red | Neutral |
| Black | Line 1 |
| White | Line 2 |
How to Override a Reversal Rotation Motor on a Dryer
A reversal rotation motor is a type of motor that is commonly used in dryers to rotate the drum in both directions. This helps to prevent the clothes from becoming tangled and to ensure that they are evenly dried. However, if the motor fails, it may be necessary to override the reversal rotation to allow the dryer to continue operating.
To override the reversal rotation motor, you will need to locate the motor and disconnect the wires that are connected to it. Once the wires are disconnected, the motor will no longer be able to rotate the drum. You can then manually rotate the drum by hand to dry the clothes.
It is important to note that overriding the reversal rotation motor is only a temporary solution. It is still necessary to replace the motor as soon as possible to ensure that the dryer operates properly.
People Also Ask
Can I override the reversal rotation motor on my dryer?
Yes, you can override the reversal rotation motor on your dryer by disconnecting the wires that are connected to it.
Is it safe to override the reversal rotation motor on my dryer?
It is generally safe to override the reversal rotation motor on your dryer. However, it is important to make sure that the override is only temporary and that the motor is replaced as soon as possible.
How can I tell if my dryer’s reversal rotation motor has failed?
There are a few signs that may indicate that your dryer’s reversal rotation motor has failed. These include:
- The dryer drum does not rotate in both directions.
- The dryer makes a loud noise when it is running.
- The dryer does not dry the clothes evenly.
