Quilting binding is the ultimate step in finishing a quilt, and it is a crucial a part of the method. It not solely finishes the sting of the quilt, nevertheless it additionally provides sturdiness and a contact of persona. There are a lot of completely different quilt binding strategies to select from, plus a wide range of supplies that can be utilized for the binding material. This text will present a step-by-step information on quilt bind by hand, one of the vital fashionable binding strategies. This information will offer you all of the strategies you have to create a ravishing and sturdy binding to your quilt.
To start, you will have to assemble your supplies. You will want a quilt that’s already quilted and trimmed, binding material, a needle, and thread. You might also wish to use a thimble to guard your fingers. After you have your supplies, you’ll be able to start the binding course of. First, you will have to chop your binding material strips. The strips needs to be minimize to the width of your required binding, plus 1/2 inch for seam allowances. The size of the strips will range relying on the scale of your quilt. After you have minimize your binding material strips, you’ll be able to start stitching them collectively. The strips needs to be sewn collectively end-to-end, utilizing a 1/4 inch seam allowance. Proceed stitching the strips collectively till you will have a steady piece of binding that’s barely longer than the perimeter of your quilt.
Supplies and Instruments for Quilt Binding
Material
Backing Material:
The backing material, which is the most important piece of material that serves as the bottom of the quilt. It needs to be barely bigger than the quilt high to permit for shrinkage and for securing the quilt high to the batting and backing. Select a material that enhances the quilt high and is sturdy sufficient to face up to repeated use and washing.
Binding Material:
The binding material, which is a strip of material that encloses the uncooked edges of the quilt. It needs to be at the very least 2.5 inches broad to offer sufficient protection and sturdiness. Choose a material that coordinates with the quilt high and backing, and that enhances the general design of the quilt.
Batting:
The batting, which is the insulating layer between the quilt high and the backing. It gives heat, loft, and form to the quilt. Select a batting materials that fits the specified weight and thickness of the quilt, akin to cotton, wool, or artificial.
Instruments
Stitching Machine:
A stitching machine is crucial for stitching the binding to the quilt. It needs to be in good working situation and able to dealing with a number of layers of material.
Needle:
Use a pointy needle that’s applicable for the kind of material used. A measurement 10 or 12 needle is usually appropriate for many quilt materials.
Thread:
Select thread that matches the colour of the binding material and that’s sturdy sufficient to carry the binding securely in place. A 100% cotton thread is commonly used for quilting.
Quilting Clips or Pins:
Quilting clips or pins are used to carry the binding in place whereas stitching. Clips are typically simpler to make use of and supply a safer maintain than pins.
Iron and Ironing Board:
An iron and ironing board are needed for urgent the binding as you sew it onto the quilt. This helps to create a neat {and professional} end.
Different Helpful Instruments:
Different helpful instruments embrace a seam ripper for eradicating stitches, a measuring tape for correct measurements, and a ruler or template for slicing the binding strips.
Selecting a Binding Material and Fashion
The selection of binding material and elegance can significantly have an effect on the general feel and look of your quilt. Listed below are some elements to think about when making your resolution:
Binding Material
The material you select to your binding needs to be sturdy and coordinate properly with the quilt high and backing. Take into account the next choices:
1. Matching material: The binding could be made out of the identical material because the quilt high or backing.
2. Coordinating material: A material that enhances the colours and patterns of the quilt high.
3. Distinction material: A material that creates a daring distinction with the quilt high.
4. Printed material: A material with a sample that provides curiosity to the binding.
5. Textured material: A material with a textured floor, akin to corduroy or denim.
6. Striped or plaid material: A material with stripes or plaids can add a singular contact to the binding.
Binding Fashion
The model of binding you select will decide how the binding is hooked up to the quilt. Listed below are among the hottest binding types:
| Binding Fashion |
|---|
| Conventional binding |
| Bias binding |
| Double fold binding |
| Machine stitched binding |
| Hand stitched binding |
Every binding model has its personal benefits and drawbacks. Conventional binding is the most typical and best to do, whereas bias binding is extra sturdy and provides an ornamental contact. Double fold binding is an efficient selection for quilts that will likely be washed regularly, and machine stitched binding is a fast and simple choice. Hand stitched binding is essentially the most time-consuming however offers essentially the most skilled end.
Reducing and Becoming a member of the Binding Strips
Earlier than slicing the binding strips, you will have to calculate how a lot material you want. Usually, you will want sufficient binding to wrap across the perimeter of the quilt twice, plus 10-12 inches for becoming a member of and ending. For instance, for a quilt that measures 60″ x 72″, you’d minimize 4 binding strips which are 168 inches lengthy (60″ + 72″ + 60″ + 72″ + 10″).
The width of the binding strips will rely upon how broad you need the completed binding to be. If you’d like a binding that’s 1″ completed, minimize the strips 2.5″ broad. For a 1.5″ completed binding, minimize the strips 3″ broad.
After you have decided how a lot and what measurement material to chop, use a rotary cutter and mat to chop the strips. Be a part of the strips collectively utilizing a diagonal seam:
Becoming a member of the Binding Strips
1. Overlap the ends of the binding strips by about 45 levels. Be certain that the correct sides of the material are dealing with one another.
2. Sew the strips collectively utilizing a scant 1/4″ seam allowance. Begin stitching about 1/4″ from the purpose of the overlap and stitch to the tip of the strips.
3. Press the seam open. It will assist to scale back bulk within the completed binding.
4. Trim the surplus material from the seam allowance on the level of the overlap. This provides you with a pleasant, clear end.
| Step | Description |
|---|---|
| 1 | Overlap the ends of the binding strips by about 45 levels. |
| 2 | Sew the strips collectively utilizing a scant 1/4″ seam allowance. |
| 3 | Press the seam open. |
| 4 | Trim the surplus material from the seam allowance on the level of the overlap. |
Mitring Corners
Mitring corners offers knowledgeable contact to your quilt binding. This is an in depth information on do it:
- Measure and minimize the binding strip to the specified size for all sides of the quilt. For every nook, you will want two strips.
- Fold one finish of every strip over at a 45-degree angle to type a triangle. The size of the triangle needs to be equal to the width of the binding strip.
- Place the triangles collectively, aligning the perimeters and the corners. Sew alongside the diagonal edge to affix them, forming a “V” form.
- Press the seam open and fold the binding strip across the nook, aligning the uncooked edges of the binding with the uncooked edges of the quilt.
- To miter the opposite nook, observe steps 1-3. Then, align the triangles in order that the factors of the “V” shapes meet. Trim the surplus material on the high and backside of the nook in order that the binding strip matches snugly across the nook.
Ending the Binding by Hand or Machine
As soon as the binding is sewn in place, it may be completed by hand or by machine. This is end it by hand:
Methodology 1: Ending the Binding by Hand
Step 1: Miter the Corners
Fold the binding over the nook of the quilt, mitering the perimeters to create a 45-degree angle. Trim any extra material.
Step 2: Blind Sew the Corners
Utilizing a needle and thread that matches the binding, sew the corners in place with small, blind stitches. Deliver the needle by way of from the again of the quilt, catching just a few threads from the within of the binding, after which insert it again into the material about 1/4 inch away. Repeat this course of till the nook is safe.
Step 3: Fold the Binding Over the Edges
Fold the binding over the uncooked edges of the quilt and topstitch it in place. Use a straight sew with an identical thread.
Step 4: Trim the Extra Binding
Trim any extra binding that extends past the perimeters of the quilt.
Methodology 2: Ending the Binding by Machine
Step 1: Set Stitching Machine
Set your stitching machine to a slim zigzag sew and choose a thread shade that matches the binding.
Step 2: Topstitch the Binding
Align the binding with the uncooked edges of the quilt and topstitch it in place. Information the sting of the binding alongside the sting of the quilt as you sew.
Step 3: Trim the Binding
Trim any extra binding that extends past the perimeters of the quilt.
Consult with the desk for a abstract of the 2 strategies:
| Methodology | Steps |
|---|---|
| Hand Ending | Mitering corners, blind stitching corners, folding over edges, trimming extra binding |
| Machine Ending | Setting stitching machine, topstitching binding, trimming extra binding |
Troubleshooting Frequent Binding Points
Binding Is Too Unfastened
- Use a narrower binding strip.
- Sew the binding nearer to the sting of the quilt.
- Use a smaller sew size.
Binding Is Too Tight
- Use a wider binding strip.
- Sew the binding farther from the sting of the quilt.
- Use a bigger sew size.
Binding Is Not Sq.
- Trim the quilt and backing squares to the identical measurement.
- Sew the binding evenly across the quilt.
- Miter the corners rigorously.
Binding Is Buckling
- Use bias binding.
Sort of Material Really helpful Bias Width Quilting cotton 2.25″ Flannel 2.5″ Silk 1.5″ - Stretch the binding as you sew it on.
- Press the binding after it’s sewn on.
Binding Is Not Laying Flat
- Use a strolling foot or even-feed foot when stitching on the binding.
- Alter the stress in your stitching machine.
- Trim the surplus seam allowance from the binding.
Binding Is Wrinkled
- Press the binding earlier than stitching it on.
- Use a lightweight contact when stitching on the binding.
- Stretch the binding gently as you sew it on.
Binding Is Coming Off
- Use a powerful thread and needle.
- Sew the binding near the sting of the quilt.
- Backstitch at first and finish of every seam.
Binding a Quilt with Bias Tape
Supplies You will Want:
- Bias tape
- Measuring tape
- Scissors
- Material glue
- Stitching machine
Step-by-Step Directions:
- Measure the perimeter of your quilt, including an additional 10-12 inches for overlap.
- Reduce a size of bias tape this size.
- Apply a skinny line of material glue to the unsuitable aspect of the bias tape.
- Fold the bias tape over the uncooked edges of the quilt, aligning the folded edge with the sting of the quilt.
- Press to set the glue.
- High sew the bias tape in place, roughly 1/8 inch from the sting of the quilt.
- Fold the bias tape to the again of the quilt.
- Trim the surplus bias tape, leaving a small overlap at the place to begin.
- Miter the corners by folding the bias tape at a 45-degree angle after which trimming the surplus. It will create a clear and professional-looking end.
| Step | Description |
|---|---|
| 1 | Measure and minimize the bias tape. |
| 2 | Apply material glue to the unsuitable aspect of the bias tape. |
| 3 | Fold the bias tape over the uncooked edges of the quilt. |
| 4 | Press to set the glue. |
| 5 | High sew the bias tape in place. |
| 6 | Fold the bias tape to the again of the quilt. |
| 7 | Trim the surplus bias tape. |
| 8 | Miter the corners. |
Easy methods to Quilt Binding
Quilt binding is the ultimate step within the quilting course of, and it serves each a practical and ornamental function. It secures the uncooked edges of the quilt and prevents them from fraying, and it additionally provides a of completion to the quilt’s general design. There are a lot of alternative ways to bind a quilt, however the most typical technique is to make use of a bias strip of material. Bias strips are minimize on a 45-degree angle to the grain of the material, which supplies them a stretchy high quality that makes them best for binding curves.
To bind a quilt utilizing a bias strip, step one is to measure the perimeter of the quilt and minimize a bias strip of material that’s twice the size of the perimeter plus 6 inches. The bias strip needs to be 2 1/2 inches broad. As soon as the bias strip is minimize, the following step is to fold it in half lengthwise and press it. Then, the bias strip is hooked up to the quilt by stitching it to the uncooked fringe of the quilt utilizing a blind sew. The blind sew is a sort of sew that’s sewn on the again of the quilt and is barely seen from the entrance. As soon as the bias strip is hooked up to the quilt, the uncooked edges of the quilt are trimmed and the binding is full.
Folks Additionally Ask About Easy methods to Quilt Binding
What’s the greatest material to make use of for quilt binding?
One of the best material to make use of for quilt binding is a tightly woven material that isn’t too thick or too skinny. Some good selections embrace cotton, linen, and silk. Keep away from utilizing materials which are stretchy or that fray simply.
How broad ought to quilt binding be?
Quilt binding needs to be 2 1/2 inches broad. This width will present sufficient protection to guard the uncooked edges of the quilt and so as to add an ornamental of completion.
How do I connect quilt binding to a curved edge?
To connect quilt binding to a curved edge, you will have to make small pleats within the bias strip. It will permit the bias strip to curve across the fringe of the quilt with out puckering. To make a pleat, merely fold the bias strip over at a 45-degree angle and press it. Then, sew the pleat in place utilizing a blind sew.
How do I end the corners of quilt binding?
To complete the corners of quilt binding, you will have to miter the corners. This implies that you’ll want to chop the bias strip at a 45-degree angle after which fold it over in order that the 2 minimize edges meet. The mitered nook can then be stitched in place utilizing a blind sew.
