Microwave ovens are a typical kitchen equipment that can be utilized to prepare dinner, reheat, and defrost meals. They’re comparatively straightforward to make use of, however eradicating them from the wall generally is a bit tougher. If you’re planning to maneuver or transform your kitchen, chances are you’ll have to take away your overhead microwave. Listed below are a number of recommendations on how one can do it safely and simply.
Earlier than you start, just remember to have all the essential instruments and supplies. You will want a screwdriver, a wrench, and a pair of pliers. You might also want a ladder in case your microwave is mounted excessive on the wall. Upon getting gathered your instruments, you’ll be able to start the elimination course of. First, unplug the microwave from {the electrical} outlet. Then, take away the mounting screws which might be holding the microwave to the wall. As soon as the screws are eliminated, you’ll be able to rigorously elevate the microwave off of the wall and set it apart.
As soon as the microwave is eliminated, you’ll be able to disconnect {the electrical} wires which might be linked to it. Watch out to not injury the wires, as this might create a hearth hazard. As soon as the wires are disconnected, you’ll be able to take away the microwave utterly. If you’re planning to maneuver the microwave to a brand new location, be sure you pack it rigorously to keep away from injury. You might also wish to contemplate hiring an expert that will help you transfer the microwave, particularly if it’s a heavy mannequin.
Disconnecting the Energy Provide
### 1. Shut off the electrical energy to the microwave.
Earlier than you start any work, it’s essential to make sure your security by disconnecting the ability provide to the microwave. Find {the electrical} panel in your residence and flip the circuit breaker that corresponds to the microwave circuit to the “OFF” place. It’s also possible to unplug the microwave from {the electrical} outlet whether it is linked to at least one.
### 2. Await the microwave to chill down.
As soon as the ability provide is disconnected, enable the microwave to chill down for at the least half-hour earlier than trying to take away it. That is to forestall any burns from residual warmth within the equipment.
### 3. Take away the mounting screws.
After the microwave has cooled, find the mounting screws that safe it to the wall or cupboard above it. These screws can often be discovered on the highest or backside of the microwave, relying on the mannequin. Use a screwdriver to take away these screws, however don’t take away the microwave from the wall or cupboard but.
### 4. Help the microwave whereas eradicating it.
With the mounting screws eliminated, you’re able to take away the microwave from its place. Get somebody that will help you elevate and assist the microwave when you rigorously slide it out of the wall or cupboard. Be aware to not drop or injury the equipment throughout this course of.
Eradicating the Mounting Screws
As soon as the ability has been disconnected, you’ll be able to start eradicating the mounting screws. These screws are usually situated on the prime of the microwave, on both aspect of the unit. They could be coated by plastic caps or covers, which you’ll gently pry off with a flathead screwdriver.
Utilizing a Phillips head screwdriver, rigorously loosen the mounting screws by turning them counterclockwise. Don’t take away the screws utterly at this level, because the microwave remains to be connected to the wall by {the electrical} wire and bracket.
As soon as the mounting screws are unfastened, you’ll be able to gently pull the microwave ahead and away from the wall. Watch out to not pull too laborious, as chances are you’ll injury {the electrical} wire or bracket.
| Software Required | Steps |
|---|---|
| Flathead screwdriver | Pry off plastic caps or covers |
| Phillips head screwdriver | Loosen mounting screws |
| Gently pull microwave ahead | Detach from wall |
Unplugging the Wiring Harness
Unplugging the wiring harness is a vital step in eradicating an overhead microwave. It requires cautious consideration to element to make sure security and stop injury to the equipment. Listed below are the steps concerned:
1. Flip Off Energy and Unplug the Microwave
Earlier than touching any electrical elements, make sure the microwave is disconnected from the ability provide. Find {the electrical} outlet and unplug the microwave from the wall. Don’t yank or pull on the wire, as this will likely injury the wiring.
2. Find and Entry the Junction Field
The junction field is a metallic enclosure that comprises {the electrical} connections for the microwave. It’s usually situated inside the cupboard or behind the microwave itself. Entry the junction field by unscrewing the quilt or eradicating any bolts or screws holding it in place.
3. Unplug the Wiring Harness
Upon getting entry to the junction field, you will note a bundle of wires linked to the microwave’s wiring harness. Every wire is usually recognized by a special coloration. To unplug the wiring harness, comply with these steps rigorously:
- Determine Terminals: Find the terminals on the junction field the place the wires from the wiring harness are linked. Terminals are usually labeled or color-coded.
- Loosen Screws: Utilizing a screwdriver, loosen the screws on the terminals to launch the wires from the wiring harness.
- Pull Wires: Gently pull every wire straight out of the terminal. Don’t pull on the wire itself, as this will likely injury the wire or the terminal.
- Disconnect Harness: As soon as all of the wires are disconnected, rigorously elevate the wiring harness away from the junction field.
Confer with this desk for a extra detailed visible information to unplugging the wiring harness:
| Step | Description |
|---|---|
| 1 | Determine terminals and loosen screws. |
| 2 | Pull wires straight out of terminals. |
| 3 | Disconnect wiring harness from junction field. |
Eradicating the Trim Plate
The trim plate is the ornamental panel that covers the sides of the microwave oven and conceals its mounting screws. To take away the trim plate, comply with these steps:
1. Unplug the microwave oven from {the electrical} outlet.
2. Find the screws that maintain the trim plate in place. They’re usually situated on the highest and backside of the trim plate.
3. Take away the screws utilizing a screwdriver. Watch out to not drop the screws.
4. Gently pull the trim plate away from the microwave oven. It ought to come off simply.
5. If the trim plate is caught, chances are you’ll want to make use of a putty knife or a skinny, flat object to softly pry it unfastened. Insert the putty knife or flat object between the trim plate and the microwave oven and thoroughly pry the trim plate away from the oven. Watch out to not injury the trim plate or the microwave oven.
As soon as the trim plate is eliminated, you should have entry to the mounting screws that maintain the microwave oven in place. Now you can proceed to the following step of the elimination course of.
Disassembling the Microwave
PREPARATIONS
Earlier than disassembling the microwave, guarantee energy provide is reduce off, plug is faraway from socket, and the machine is chilly.
REMOVING THE CABINET
Determine the mounting screws or bolts securing the microwave to the cupboard. Unscrew or unbolt them rigorously. Grip the microwave firmly, elevate it straight up off the cupboard, and set it apart.
DISCONNECTING THE WIRING
Find the wiring harness connecting the microwave to the ability provide and cupboard. Disconnect the harness by unplugging the connectors or unscrewing the terminals. Label wires if essential for simpler reassembly.
REMOVING THE MOUNTING BRACKETS
Unfasten the mounting brackets attaching the microwave to the wall or ceiling. These could also be secured with screws or bolts; use applicable instruments to take away them.
DETACHING THE DOOR
Open the microwave door absolutely. Find the hinges connecting the door to the microwave physique. Unscrew or unbolt the hinges and thoroughly elevate the door off the microwave.
ACCESSING THE INTERNAL COMPONENTS
As soon as the door is eliminated, you’ll be able to entry the inner elements of the microwave. These could embody the magnetron, waveguide, fan motor, and turntable motor. Deal with elements gently to keep away from injury.
ELECTRICAL COMPONENTS
MAGNETRON
The magnetron is a vacuum tube that generates microwaves. It’s situated within the base of the microwave oven and is answerable for heating the meals. The magnetron is a vital part and may solely get replaced by a certified technician.
WAVEGUIDE
The waveguide is a metallic tube that carries microwaves from the magnetron to the cooking chamber. You will need to preserve the waveguide clear and freed from obstructions.
FAN MOTOR
The fan motor circulates air contained in the microwave oven to chill the elements and stop overheating. The fan motor is often situated behind the microwave oven.
TURNTABLE MOTOR
The turntable motor rotates the turntable contained in the microwave oven, making certain that meals is cooked evenly. The turntable motor is often situated within the backside of the microwave oven.
Cleansing the Microwave
1. Unplug the microwave.
Earlier than you start cleansing, be sure you unplug the microwave from {the electrical} outlet. It will stop the microwave from by accident turning on if you are cleansing it.
2. Take away the turntable and turntable ring.
The turntable and turntable ring may be eliminated by merely lifting them out of the microwave. Make sure to wash these things in sizzling, soapy water and dry them totally earlier than changing them.
3. Clear the inside of the microwave.
The inside of the microwave may be cleaned with a gentle detergent and water. Use a sponge or fabric to wipe down the inside surfaces, together with the door, the ceiling, and the perimeters. Make sure to rinse the inside totally with clear water and dry it with a clear fabric.
4. Clear the outside of the microwave.
The outside of the microwave may be cleaned with a gentle detergent and water. Use a sponge or fabric to wipe down the outside surfaces, together with the door, the perimeters, and the highest. Make sure to rinse the outside totally with clear water and dry it with a clear fabric.
5. Clear the door gasket.
The door gasket is a rubber seal that helps to maintain the microwave door closed. Over time, the door gasket can develop into soiled and greasy. Use a sponge or fabric to wipe down the door gasket with a gentle detergent and water. Make sure to rinse the door gasket totally with clear water and dry it with a clear fabric.
6. Clear the vent.
The vent is situated on the highest or aspect of the microwave. It’s used to exhaust air from the microwave. Over time, the vent can develop into clogged with mud and particles. Use a vacuum cleaner to wash the vent. Make sure to take away any mud or particles from the vent.
7. Clear the microwave filter.
The microwave filter is situated behind the vent. It’s used to lure grease and smoke from the microwave. Over time, the microwave filter can develop into clogged with grease and smoke. You will need to clear the microwave filter recurrently to make sure that the microwave is working correctly. To scrub the microwave filter, take away it from the microwave and wash it in sizzling, soapy water. Make sure to rinse the microwave filter totally with clear water and dry it totally earlier than changing it.
| Cleansing Process | Frequency |
|---|---|
| Clear the inside of the microwave | Month-to-month |
| Clear the outside of the microwave | Month-to-month |
| Clear the door gasket | Month-to-month |
| Clear the vent | Each 3 months |
| Clear the microwave filter | Each 6 months |
Reinstalling the Microwave
1. Flip off the ability to the microwave on the circuit breaker.
2. Take away the mounting screws that maintain the microwave to the cupboard.
3. Rigorously elevate the microwave off the mounting bracket.
4. Take away the ability wire from the outlet.
5. Take away the exhaust duct from the microwave.
6. If the microwave is vented exterior, take away the vent cap from the outside wall.
7. Clear the mounting floor and the again of the microwave.
8. Apply a bead of caulk across the perimeter of the mounting floor. It will assist to seal the microwave and stop drafts.
| Step | Motion |
|—|—|
| 1 | Flip off the ability to the microwave on the circuit breaker. |
| 2 | Take away the mounting screws that maintain the microwave to the cupboard. |
| 3 | Rigorously elevate the microwave off the mounting bracket. |
| 4 | Take away the ability wire from the outlet. |
| 5 | Take away the exhaust duct from the microwave. |
| 6 | If the microwave is vented exterior, take away the vent cap from the outside wall. |
| 7 | Clear the mounting floor and the again of the microwave. |
| 8 | Apply a bead of caulk across the perimeter of the mounting floor. It will assist to seal the microwave and stop drafts. |
9. Place the microwave on the mounting bracket and align the screw holes.
10. Insert the mounting screws and tighten them securely.
11. Join the ability wire to the outlet.
12. Set up the exhaust duct to the microwave.
13. If the microwave is vented exterior, set up the vent cap on the outside wall.
14. Activate the ability to the microwave on the circuit breaker.
15. Take a look at the microwave to ensure it’s working correctly.
Reconnecting the Energy Provide
Step 1: Unplug the Microwave.
Earlier than touching any wires, be sure that the microwave is totally disconnected from the ability supply. Find the ability wire and pull the plug from the wall outlet.
Step 2: Determine the Wires.
Inside {the electrical} field, you’ll find a number of wires linked to the microwave. These wires will usually be black, white, and inexperienced (or naked copper) and are held along with wire nuts.
Step 3: Take away the Wire Nuts.
Rigorously take away the wire nuts by twisting them counterclockwise. Be cautious to not injury the wires.
Step 4: Separate the Wires.
As soon as the wire nuts are eliminated, gently separate the black and white wires from one another. The inexperienced (or naked copper) wire is the bottom wire and may stay linked.
Step 5: Join the New Microwave.
Align the wires from the brand new microwave with the corresponding wires from {the electrical} field. Twist the black wire from the brand new microwave with the black wire from the field, and do the identical for the white wires.
Step 6: Safe the Wire Nuts.
Place a brand new wire nut over every set of twisted wires and tighten it clockwise till comfortable. Make sure that the wires are securely linked.
Step 7: Take a look at the Wiring.
Earlier than reconnecting the ability, double-check your connections utilizing a multimeter to make sure correct continuity and no brief circuits.
Step 8: Reconnect the Energy.
Plug the microwave energy wire again into the wall outlet and activate the breaker or fuse to revive energy to the equipment.
Step 9: Take a look at the Microwave.
Press the ability button on the microwave to make sure that it’s functioning appropriately. If the microwave doesn’t activate or operates abnormally, repeat the above steps to examine for any unfastened connections or wiring errors.
Testing the Microwave
Earlier than trying to take away the microwave, it is essential to make sure it is turned off and unplugged from the ability supply. Comply with these steps to confirm the microwave’s standing:
1. Test the Energy Swap
Find the ability swap on the microwave’s entrance or aspect panel. Make certain it is turned to the “Off” place.
2. Unplug the Microwave
Find {the electrical} outlet the place the microwave is plugged in. Firmly grasp the plug and pull it straight out of the outlet.
3. Await Capacitor to Discharge
After unplugging the microwave, enable a couple of minutes for the capacitor to discharge. It will stop any electrical shock hazard.
4. Open the Microwave Door
As soon as the capacitor has discharged, open the microwave door to launch any remaining vitality.
5. Test for Residual Warmth
Really feel the within and outdoors of the microwave to make sure it is utterly cool. If it is nonetheless heat, wait longer earlier than continuing.
6. Visually Examine the Microwave
Study the microwave for any injury or unfastened components. If you happen to discover something uncommon, don’t try to take away it your self and make contact with a certified equipment restore technician.
7. Collect Mandatory Instruments
You’ll probably want a Phillips head screwdriver and a flathead screwdriver to take away the microwave.
8. Put on Protecting Gear
Placed on security glasses and gloves to guard your self from sharp edges or electrical elements.
9. Disconnect Electrical Wires
As soon as the microwave is faraway from the wall, rigorously disconnect {the electrical} wires from the terminal block. Notice the place of every wire for reconnection later.
10. Take away the Mounting Bracket
Find the mounting bracket that secures the microwave to the wall. Utilizing the suitable screwdriver, take away the screws or bolts that maintain the bracket in place. Watch out to not drop the microwave when eradicating it from the bracket.
How To Take away A Overhead Microwave
Eradicating an overhead microwave generally is a daunting activity, however it’s undoubtedly doable to do it your self with the precise instruments and a bit little bit of know-how. Listed below are the steps on how one can do it:
- Flip off the ability to the microwave. This may be performed by unplugging it from the outlet or by turning off the breaker that controls the ability to the microwave.
- Take away the mounting screws. There are often 4 screws that maintain the microwave in place. These screws are situated on the highest of the microwave, close to the again. Use a screwdriver to take away the screws.
- Rigorously elevate the microwave off of the wall. As soon as the screws are eliminated, you’ll be able to rigorously elevate the microwave off of the wall. Make sure to assist the load of the microwave along with your different hand.
- Disconnect the wiring. As soon as the microwave is off of the wall, you might want to disconnect the wiring. There are often two wires that join the microwave to the ability supply. Use a pair of pliers to disconnect the wires.
- Take away the microwave from the kitchen. As soon as the wiring is disconnected, you’ll be able to take away the microwave from the kitchen. Make sure to elevate the microwave rigorously and keep away from bumping it into something.
Individuals Additionally Ask About How To Take away A Overhead Microwave
How do I take away a microwave from a cupboard?
To take away a microwave from a cupboard, you have to to:
- Open the cupboard door.
- Find the screws which might be holding the microwave in place.
- Take away the screws.
- Rigorously elevate the microwave out of the cupboard.
How do I take away a microwave from a wall bracket?
To take away a microwave from a wall bracket, you have to to:
- Flip off the ability to the microwave.
- Take away the screws which might be holding the microwave to the wall bracket.
- Rigorously elevate the microwave off of the wall bracket.
- Disconnect the wiring from the microwave.
How do I take away a inbuilt microwave?
To take away a inbuilt microwave, you have to to:
- Flip off the ability to the microwave.
- Take away the trim across the microwave.
- Take away the screws which might be holding the microwave in place.
- Rigorously elevate the microwave out of the cupboard.
- Disconnect the wiring from the microwave.
