1 | How to Replace Filter in GE Refrigerator

Filter in GE Refrigerator

Maintaining the cleanliness and optimal performance of your GE refrigerator is essential for preserving the freshness of your food and beverages. Among the crucial maintenance tasks is regularly replacing the water filter to ensure clean, great-tasting water and ice. This simple yet vital step can make a significant difference in the quality of your water and the overall functionality of your refrigerator.

Changing the water filter in your GE refrigerator is a straightforward process that can be completed in just a few minutes. By following a few simple steps, you can ensure that your refrigerator is equipped with a fresh filter, ready to deliver pure and refreshing water. Additionally, regular filter replacement helps prevent the buildup of impurities and contaminants, which can affect the taste and quality of your water.

Before you begin the filter replacement process, locate the water filter housing, which is typically found inside the refrigerator compartment or on the exterior of the refrigerator door. Once you have identified the housing, follow the manufacturer’s instructions for removing the old filter and inserting the new one. Remember to dispose of the old filter properly and reset the filter indicator light, if applicable. With a fresh water filter in place, you can rest assured that your GE refrigerator is providing you with clean, filtered water for drinking, cooking, and making ice.

$title$

Identifying the Filter Location

Locating the water filter in your GE refrigerator is crucial before attempting to replace it. The filter’s position may vary depending on the refrigerator model, but generally, there are a few common locations to check:

Behind the Grille

Open the refrigerator door and look for a removable grille at the top or bottom.
Slide or lift the grille away from the refrigerator to reveal the filter.

Inside the Fridge Compartment

In some models, the filter is located inside the fridge compartment itself.
Look for a smaller door or panel on the ceiling or back wall of the refrigerator.
Open the door or panel to access the filter.

Beneath the Refrigerator

Pull the refrigerator slightly away from the wall to access the bottom.
Locate the filter housing, which may be a cylindrical or rectangular unit attached to the water line.

Additional Notes

Consult your refrigerator’s user manual for specific instructions on locating the water filter.
If you have difficulty finding the filter, contact GE customer support for assistance.

Table: Common Filter Locations in GE Refrigerators

Model Type	Filter Location
Top-Freezer Refrigerator	Behind the grille at the top of the fridge
Bottom-Freezer Refrigerator	Inside the fridge compartment behind a small door
Side-by-Side Refrigerator	Beneath the refrigerator, attached to the water line

Gathering the Necessary Tools

To replace the filter in your GE refrigerator, you will need the following tools:

A new GE refrigerator water filter
A screwdriver (optional)

Selecting the Right Filter

GE recommends using only genuine GE refrigerator water filters to ensure optimal performance and water quality. The model number of the correct filter for your refrigerator is typically printed on the front of the filter housing or in the refrigerator’s user manual. If you are unsure which filter to purchase, consult the GE website or contact GE customer service.

Refrigerator Model	Filter Model
GSH25JSMSS	GSWF
GFE28GYNFS	MWF

Preparing the Work Area

Before starting the filter replacement process, clear the area around the filter housing of any obstacles. You may also want to place a towel or pan underneath the filter housing to catch any water that may spill.

Shutting Off the Water Supply

Before you start replacing the filter on your GE refrigerator, it’s crucial to shut off the water supply to prevent any unexpected leaks or spills. Here are the steps you need to follow:

Locate the water supply valve. It’s usually situated behind or underneath the refrigerator, near the water supply line.
Turn the valve handle clockwise to shut off the water flow. The direction of rotation may vary depending on the valve type, so refer to the manufacturer’s instructions if necessary. If the valve is difficult to turn, use a pair of pliers or a wrench for assistance.

Checking for Leaks (Optional but Recommended)

Once the water valve is turned off, it’s recommended to check for any leaks in the water line or connections. Here’s how:

a. Remove the filter housing:

Open the refrigerator door and locate the filter housing, typically situated in the top right or left corner. Depress the release button to detach the housing from the refrigerator.

b. Inspect the water line:

Look for any visible cracks, cuts, or bulges in the water line connected to the filter housing. If you find any damage, it’s advisable to replace the water line before continuing.

c. Check the connections:

Examine the connections where the water line meets the filter housing and the refrigerator’s water supply valve. Ensure that the connections are securely fastened and free from any leaks.

Once you’ve checked for leaks, you can proceed with the filter replacement process.

Releasing the Filter Pressure

Before replacing the filter, it’s crucial to release the water pressure within the system to prevent any potential spills or messes. Follow these detailed steps to ensure a safe and hassle-free filter replacement:

1. Locate the Water Supply Valve

Look for the main water supply valve usually located under the sink. It’s typically a small, plastic handle that controls the flow of water to the refrigerator. Turn the valve clockwise to shut off the water supply.

2. Open the Water Dispenser

Dispense water from the refrigerator’s water dispenser until no more water comes out. This will help release the pressure in the line.

3. Disconnect the Water Line

Locate the water supply line that connects to the back of the refrigerator. Use a wrench or pliers to loosen the compression nut that secures the line. Hold a bucket or towel underneath the connection to catch any water that may leak out.

4. Remove the Old Filter and Install the New One

Once the water line is disconnected, you can access the filter housing. Refer to the manufacturer’s instructions or find the specific model number of your GE refrigerator online to determine the exact process. In general, you’ll need to:
– Locate the filter housing, usually inside the refrigerator or behind the grille at the bottom of the appliance.
– Twist the old filter counterclockwise to remove it and discard it.
– Insert the new filter into the housing and twist it clockwise until it’s snug.
– Before reconnecting the water line, reset the filter indicator light by following the manufacturer’s instructions.

Filter Location	Access Method
Inside the refrigerator	Remove the grille or shelf to expose the filter
Behind the grille at the bottom of the refrigerator	Remove the grille to access the filter

Removing the Old Filter

1. Locate the filter: The filter is usually located inside the refrigerator compartment, behind the crisper drawers.

2. Turn off the water supply: Turn the water valve (located behind the refrigerator) to the “off” position.

3. Release the pressure from the water line: Dispense water from the dispenser until the water flow stops completely.

4. Disconnect the water lines: Locate the two water lines connected to the filter and disconnect them by pressing the release button.

5. Remove the old filter: Grip the old filter firmly and twist it counterclockwise to remove it from the filter housing.

Additional details for removing the old filter:

a. Use a towel: Place a towel underneath the filter to catch any water that may leak out.

b. Be careful with the water lines: Avoid kinking or damaging the water lines when disconnecting them.

c. Check for leaks: After removing the old filter, check the water lines and filter housing for any leaks.

Inserting the New Filter

With the old filter removed, it’s time to insert the new one. Here are the detailed steps you need to follow:

Unwrap the New Filter: Remove the plastic packaging from the new filter.
Locate the Filter Housing: Find the filter housing located in the back wall of the refrigerator compartment (usually near the bottom).
Align the Filter: Line up the new filter with the guiding arrows or tabs on the filter housing.
Insert the Filter: Push the filter into the housing until it fits snugly in place.
Secure the Filter: Twist or turn the filter clockwise until it locks into place (approximately a quarter or half turn).
Reset the Filter Indicator (optional): If your refrigerator has a filter indicator light, press the reset button to turn off the light, indicating that the filter has been replaced. For detailed instructions, refer to your refrigerator’s user manual.

Note: If you encounter any difficulties inserting the filter, check to ensure it is correctly aligned and that there are no obstructions preventing its insertion. If the filter still won’t fit, contact a qualified appliance repair technician for assistance.

Filter Type	Reset Method
Standard Filter	No reset required
SmartWater Filter	Press and hold the “Filter Reset” button for 5 seconds

Tightening the Filter Housing

7. Tightening the Filter Housing

Once the filter cartridge is properly inserted, it’s time to tighten the filter housing. This step is crucial to ensure that the filter is secure and prevents water from leaking. Here are the detailed steps on how to tighten the filter housing:

Align the Filter Housing: Grip the filter housing and align it with the filter head.
Tighten by Hand: Begin tightening the filter housing by hand, turning it clockwise. Ensure that it’s tightened securely but avoid overtightening.
Use a Filter Wrench (Optional): If you have difficulty tightening the filter housing by hand, you can use a filter wrench. Insert the wrench into the notches on the filter housing and turn it clockwise to tighten.
Quarter-Turn Rule: As a general rule of thumb, tighten the filter housing by a quarter turn after it becomes hand-tight. This will ensure a snug fit without overtightening.
Check for Leaks: Once the filter housing is tightened, turn on the water supply and check for any leaks around the filter head or connections. If you notice any leaks, retighten the filter housing as necessary.
Reset the Filter Indicator: If your refrigerator has a filter indicator light, press and hold the reset button for a few seconds to turn it off. This will reset the filter life timer and indicate that the new filter has been installed.
Enjoy Clean Water: Your GE refrigerator is now equipped with a fresh and functioning water filter. Enjoy the peace of mind of having access to clean, filtered water at all times.

Resetting the Filter Indicator Light

After replacing the filter, you need to reset the filter indicator light to indicate that a new filter has been installed.

Locate the Filtered Water Indicator button on the refrigerator’s control panel. It may be labeled as "Filter Indicator" or "Filter Reset."
Press and hold the Filtered Water Indicator button for 5-10 seconds.
The indicator light will blink or illuminate briefly, indicating that the reset is complete.
Some models may display a message on the display screen confirming the reset.

Detailed Instructions for GE Refrigerators:

Press the Refrigerator or Freezer button on the control panel repeatedly until the display shows Status.
Locate the Filter Indicator option.
Press the Adjust button to toggle between Yes and No.
Select Yes to indicate that the filter has been replaced.
Press the Refrigerator or Freezer button to exit the Status menu.

Table of Filter Indicator Light Reset Options:

Refrigerator Model	Filter Indicator Light Reset Button
GSS25	Filtered Water Indicator
GFE28	Filter Indicator
PSE25	Filtered Water Indicator
PFE28	Filter Indicator
GSH25	Filtered Water Indicator
GFH28	Filter Indicator

How to Replace Filter in GE Refrigerator

Replacing the filter in your GE refrigerator is a quick and easy task that can help keep your fridge running at its best. Here’s a step-by-step guide on how to do it:

Locate the filter. The filter is typically located in the upper right-hand corner of the refrigerator compartment. It will have a blue handle and a label that says “Replace Filter.”
Turn off the water supply to the refrigerator. The water supply valve is usually located behind the refrigerator. Turn the valve clockwise to turn off the water.
Remove the old filter. Grasp the filter handle and pull it straight down to remove it from the refrigerator. There may be some water that drips out, so be sure to have a towel handy.
Insert the new filter. Line up the new filter with the housing and push it straight up into place. You should hear a click when the filter is properly installed.
Turn on the water supply to the refrigerator. Open the water supply valve by turning it counterclockwise.
Run water through the filter. Press the water dispenser button for several minutes to run water through the filter and remove any air bubbles.