**How to Set Steering Wheel Endpoints Felony 6s**
Setting the steering wheel endpoints on a Felony 6s is a crucial step in ensuring optimal performance and safety while driving. These endpoints determine the maximum and minimum steering angles, which directly impact the vehicle’s handling and maneuverability. Incorrectly set endpoints can lead to compromised steering response, reduced stability, and increased risk of accidents. Therefore, it is essential to follow the proper procedures and utilize the correct tools to set the steering wheel endpoints accurately. This guide will provide a comprehensive overview of the steps involved in setting steering wheel endpoints on a Felony 6s, ensuring that your vehicle operates within optimal parameters.
Before commencing the process, gather the necessary tools, including a steering wheel alignment gauge, a torque wrench, and a socket set. It is recommended to seek professional assistance if you lack the necessary skills or expertise. Firstly, position the vehicle on a flat and level surface and engage the parking brake. Disconnect the negative battery terminal to prevent accidental electrical discharge. Next, remove the steering wheel by carefully disassembling the bolts or screws securing it to the steering column. Once the steering wheel is detached, you can proceed with setting the endpoints.
Identifying the Steering Wheel End Points
The steering wheel end points are the physical limits of how far the steering wheel can turn in either direction. These end points are important because they determine the maximum amount of steering angle that the vehicle can achieve. Identifying the steering wheel end points is a relatively simple process.
1. Turn the Steering Wheel to the Left
Start by turning the steering wheel all the way to the left. You will feel the steering wheel stop turning at a certain point. This point is the left steering wheel end point.
2. Turn the Steering Wheel to the Right
Next, turn the steering wheel all the way to the right. You will again feel the steering wheel stop turning at a certain point. This point is the right steering wheel end point.
3. Measure the Steering Angle
Once you have identified the steering wheel end points, you can measure the steering angle. To do this, you will need a steering wheel angle sensor. A steering wheel angle sensor is a device that measures the angle of the steering wheel in relation to the vehicle’s center line. Once you have a steering wheel angle sensor, you can attach it to the steering wheel and measure the steering angle at the left and right steering wheel end points.
4. Calculate the Maximum Steering Angle
The maximum steering angle is the difference between the left and right steering wheel end points. To calculate the maximum steering angle, simply subtract the left steering wheel end point angle from the right steering wheel end point angle. The result is the maximum steering angle.
| Steps | Details | |
|---|---|---|
| 1 | Turn the Steering Wheel to the Left | Turn the steering wheel all the way to the left until it stops turning. |
| 2 | Turn the Steering Wheel to the Right | Turn the steering wheel all the way to the right until it stops turning. |
| 3 | Measure the Steering Angle | Attach a steering wheel angle sensor to the steering wheel and measure the steering angle at the left and right steering wheel end points. |
| 4 | Calculate the Maximum Steering Angle | Subtract the left steering wheel end point angle from the right steering wheel end point angle. The result is the maximum steering angle. |
Adjusting the Left End Point
6. Fine-Tune the Left End Point
With the left end point set as a starting point, you can now fine-tune it to ensure maximum steering range without interference. To do this:
- Turn the steering wheel all the way to the left, holding it for a few seconds. This will allow the steering system to settle into its extreme left position.
- Release the wheel and double-check its position using a wheel alignment machine or by measuring the distance between the steering wheel and the seat.
- If needed, adjust the left end point slightly (typically by 1-2 degrees) to provide a slight amount of play to prevent binding when the steering is returned to center.
- Repeat steps 2-3 until you achieve a satisfactory range of motion.
| Adjustment Increment | Effect on Steering Range |
|---|---|
| 1 degree clockwise | Increase left end point by 1 degree |
| 1 degree counterclockwise | Decrease left end point by 1 degree |
Verifying the End Point Adjustments
Once the end points have been set, it’s crucial to verify their accuracy. Follow these steps:
1. Check the Center Position
Turn the steering wheel until it is centered and the vehicle is driving straight. Ensure that the steering wheel is not angled toward either side.
2. Adjust the Toe-in
Use a measuring device to check the toe-in. Adjust the tie rods as necessary to achieve the desired toe-in specification. This ensures that the wheels are pointing slightly inward, which improves stability and tire life.
3. Check the Caster and Camber
Use an alignment machine to measure the caster and camber angles. Adjust the suspension components as required to achieve the specified values. These angles impact vehicle handling and tire wear.
4. Road Test the Vehicle
Take the vehicle for a road test to assess if the end points are set correctly. Note any unusual handling or tire wear patterns. If necessary, make further adjustments until the vehicle drives smoothly and predictably.
5. Inspect the Steering System
Inspect the steering system, including the steering rack, linkages, and tie rods. Ensure that all components are in good condition and free of excessive wear or damage. This helps prevent steering issues in the future.
6. Measure the Turning Radius
Measure the turning radius of the vehicle by driving it in a circle. Compare the measured value to the manufacturer’s specifications. This ensures that the steering end points allow for adequate maneuverability.
7. Recalibrate the Steering Assist Systems (if applicable)
If the vehicle is equipped with steering assist systems, recalibrate them after setting the end points. This includes systems such as lane departure warning, blind-spot monitoring, and other electronic steering aids. Proper calibration ensures that these systems function correctly and assist the driver effectively.
Resetting the Steering Angle Sensor
8. Connecting the scan tool to the vehicle’s OBDII port and selecting the appropriate menu options for steering angle sensor calibration. The specific steps may vary depending on the scan tool being used.
- Connecting the scan tool: Locate the OBDII port on the vehicle, typically located under the dashboard on the driver’s side. Plug the scan tool into the port.
- Selecting the menu options: Turn on the scan tool and navigate to the menu options related to steering angle sensor calibration. These options may be labeled as "Steering Angle Reset," "SAS Calibration," or similar.
- Confirming calibration: Once the scan tool is connected and the calibration process has been initiated, follow the prompts on the screen to complete the procedure. This may involve starting the engine, turning the steering wheel to specific positions, or driving the vehicle in a straight line for a short distance.
- Verifying calibration: After the calibration process is complete, verify that the steering angle sensor is functioning correctly by turning the steering wheel and observing the corresponding output on the scan tool or instrument cluster. If the sensor is not calibrated properly, repeat the calibration procedure or consult a professional automotive technician for further assistance.
| Step | Action |
|---|---|
| 1 | Locate the OBDII port and plug in the scan tool. |
| 2 | Select the “Steering Angle Reset” or “SAS Calibration” option in the scan tool menu. |
| 3 | Follow the on-screen prompts to complete the calibration process. |
| 4 | Verify the calibration by turning the steering wheel and observing the sensor output. |
Confirming the Correct Steering Wheel Range
To ensure accurate end-point setting, it’s crucial to verify the steering wheel range specified by the manufacturer.
Here’s a step-by-step guide to confirm the correct range:
- Identify the vehicle’s specification manual: Locate the document that provides detailed information about the vehicle, including steering wheel range parameters.
- Find the steering wheel range section: Within the manual, search for a section specifically dedicated to steering wheel range or turn radius.
- Extract the endpoint values: Identify the values listed for the maximum and minimum steering wheel angles, typically measured in degrees.
- Check for front wheel toe: Ensure that the front wheel toe is set to the manufacturer’s specifications before setting the end-points, as toe adjustments can affect the steering wheel range.
- Account for tire wear and suspension alignment: Worn tires or misaligned suspension can impact the steering wheel range. If necessary, replace tires and perform a suspension alignment to ensure accurate end-point setting.
- Inspect mechanical components: Verify that all mechanical components, such as steering rack, tie rods, and ball joints, are functioning properly and not causing any binding or resistance in the steering system.
- Use an alignment machine: An alignment machine can be used to confirm the steering wheel range and provide precise end-point data.
- Check for column tilt: On vehicles with adjustable steering columns, ensure that the column tilt is set to the neutral position before measuring the steering wheel range.
- Calibrate the steering wheel sensor: Once the end-points are set, use a diagnostic tool to recalibrate the steering wheel sensor, which will adjust the vehicle’s steering system to match the new range.
Following these steps will help you accurately confirm the correct steering wheel range for your Felony 6s, ensuring the proper function of the steering system and optimal vehicle handling.
How to Set Steering Wheel Endpoints on a Felony 6s
1. **Identify the steering wheel endpoint adjustment screws.** These are typically located on the bottom of the steering column, near the firewall.
2. **Loosen the adjustment screws with a wrench.** Do not remove the screws completely.
3. **Turn the steering wheel to the desired endpoint.** The steering wheel should be turned until it stops against the steering stop.
4. **Tighten the adjustment screws.** Do not overtighten the screws.
5. **Verify the endpoint adjustment.** Turn the steering wheel from lock to lock to ensure that it stops at the desired endpoints.
People Also Ask
How to adjust steering wheel sensitivity on a Felony 6s?
The steering wheel sensitivity can be adjusted by changing the “Steering Sensitivity” setting in the Felony 6s’s menu. There are three sensitivity settings to choose from: Low, Medium, and High. To change the sensitivity setting, follow these steps:
- Press the “Menu” button on the Felony 6s controller.
- Use the D-pad to navigate to the “Settings” tab.
- Select the “Steering Sensitivity” setting.
- Use the D-pad to select the desired sensitivity setting.
- Press the “Back” button to save the changes.
How to calibrate steering wheel on a Felony 6s?
To calibrate the steering wheel on a Felony 6s, follow these steps:
- Connect the Felony 6s to a computer using a USB cable.
- Download and install the Felony 6s software from the Axial website.
- Open the Felony 6s software.
- Click on the “Calibration” tab.
- Follow the on-screen instructions to calibrate the steering wheel.
